Search results

Need 3 crates and a couple pallets of equipment from Ozark Mo to Greenville, SC About 8,000 lbs of engine parts.

I appreciate the offer bikeman. I was told about Joe Nuzzolese silverwingstrans15@gmail.com. He is recovering both of them for me next week and delivering to SC. He is from Fayettenam too! Thanks again!

I have a MEP-803A that is scheduled for recovery on 11/12/2015 at 10am. Can someone pickup and I can get it. I can also pay to ship to SC. I have an 802A at Bragg also. I will be working in Raleigh next week so I could meet you for pickup in the evenings. PM or call 864-517-2707 Thanks!!!

The pattern for the Severe Duty 12 is 8.5 inches across on center ( 4 holes on each side) 6.5 and 4.5 on center http://www.warn.com/industrial/severe_duty/images/912531-Datasheet-71853-SRS%2012-A-2D%20SEVERE%20DUTY.pdf

I used a RG-31 bumper with integrated winch protection system.

I would wrap the front and sides of the winch with 1/2 AR 500 plate. You will need to cut out the oval in the front plate to match the oval in the fairlead. I would make it where it has a 1/4 inch gap between the winch and 1/2 inch plate so you have a minor gap area between the winch and...

Ran into a braking problem last month. Every time I braked, the truck seemed to struggle to pull the slightest hill. 20 miles and I could fry eggs on all 4 rear rims. The vent hole was plugged on the glad hand! I am going to repack bearings before I put it back on the road! One little thing...

I agree with the nylon. I have used tygon with nitromethane. Since bio crap came out and messed my fuel system up on my 939, I used the nylon hose to a re-circulation pump which is used to filter / heat to my fuel to keep it clean and warm in winter. I just used a 24v pump off a MEP. I can...

I have heard that the winch just turns into a block of ice with synthetic rope in very cold climates. Most Scandinavian folks prefer wire! Also you have to put a heat covering over the synthetic for the first wrap on a series 12 or 18 winch due to heat. There is a better synthetic rope out...

Another consideration is if you have more than 1 power panel in your home. If so I would go with a MEP-004. You can feed the two panels without converting from 3 phase to single phase. I just used a generator power distribution box and I can feed two panels easily. You can use a clamp on amp...

I have 3 hoods and roughly 6 pallets. Some can be consolidated as I just purchased 4 pallets which have a couple of small boxes each. These can easily go on one pallet. I only need one hood for a 939 so if you know of anyone needing some then let me know.

Anyone near Owego? I would really like to find someone to check some items and handle the load out.

I have a lot of stuff up at gimpyrobbs. I just saw your post.

That is a very good price. I paid $5 a mile a year ago. Has anyone ever sent a vehicle by train? I have a friend that does the cross country rally and he sends his jeep to California from Raleigh by train and then takes a plane out a week later.

Just shipped out 16 winches going to Indiana, Illinois, Reno, LA and Alaska. Wish I would have known you were going that way. I could have paid you instead of the freight companies :)

I have had more than one air line or electrical wire crossed. Makes you wonder!

Most of them used a drop over cab. You take the windshield, doors, and top off and it fits over the existing cab. I have lots of pictures. There is also a guard that goes in front of the heater and another for covering the windshield washer area. You also have a plate that goes below the...

Probably didn't have the right lobbyists in DC at the time with the right amount of kickback money!

Need pickup and delivery of 3 palletized M939 hoods from Groveport, OH to SC.

It would require 600 amps at 12 volts. You can buy a motor from warn but it is around 1k.