Search results

NO READING ON KILOWATT (LOAD)METER (M2) WHEN LOAD IS APPLIED Disconnect P17 from A8 and perform the following tests: a. Set multimeter to read resistance. Multimeter should read 100 ohms at LOAD meter terminals on back of meter. If reading is less than 100 ohms,remove and replace LOAD meter (WP...

And were up and running. Seems Fuel gauge now does not work after it shorting out and the plugs GFI is faulty. Going to have to troubleshoot the fuel gauge in a bit. I can care less about the plug ATM. https://youtu.be/y5bsDREkJ5A Also a big thanks to Dav5 for sending the shim stock.

Ok, there are fuses inside the Frequency Converter. The fuses look like little black resistors they are numbered F1-F4, you may have to scrape through some coating to get a resistance reading. Try testing those fuses, then we'll go from there. A replacement Frequency Converter would probably...

Have you went threw the troubleshooting steps in the TM?

Any update on those brushes you ordered? Sent from my SM-G935P using Tapatalk

INITIAL ADJUSTMENTS, BEFORE USE AND SELF-TESTThe diesel engine must be broken in, avoiding heavy loads (no greater than 75%), for a period of at least twenty(20) hours to ensure proper operation of the generator set. After the initial break-in period, intake and exhaustvalve clearances must be...

The cutting boards measured .030" I tried them, way too think to even let the rotor fit in stator. I took the screw our of my both of my feeler gauges to used them as a space on the side that was too close before. If i hit the rotor with a rubber mallet it will seat its self, once i try to...

I ended up ordering 100' of SOOW 10/4 wanted something heavy enough for my Mep-831a. Put a box on the end with two GFCI that are TR and WR.

Never knew these were a thing, if the plastic cutting boards don't work out. I might order a set.

No luck way too tight to release the file folder intact. Going to see how the plastic cutting boards work out.

I will give that a try, thanks.

Replace the oil seal, I was missing the head washers that go under the rocker cover. Had some washer on hand the were a little to wide, so I swapped out the ones that are not under cover. Also replace the flywheel cover vibration absorbers they turned into old bubble gum. Also replaced the seal...

Give this a read I think it may help you out.

Generator came in handy today lost power for little over an hour today, from a wind storm. Was able to power all the TVs and satellite and a few other things. Going to be looking into a transfer switch some time soon, been looking at a "Generac 6852 Home Link Upgradeable Transfer Switch Kit 30...

What about a exhaust flapper? Cant live in west Texas and not have one, I think its a rule here. I'm just joking, thanks for the info Dewie. Also changed the oil at 10hr mark of breaking in sine honing the engine. About 10hrs more to go then back to the regular scheduled LO.

I did think about it before, decided to wait until the unit runs like it should. It would need a flexible pipe after the 90 degree turn to isolate vibrations from the engine. One of those mesh ones probably, as for the muffler its self I have no idea what on to get. Never have done anything like...

Figured out what was making that noise, the rotor was rubbing on the stator, tried to insert a .010 gauge no good one that side. other side has a really big gap. I noticed that when I first tore apart the set. I removed and reinstalled the rotor and now the .010 gauge can fit. From TM Using a...

Ill order 100' SJOOW 10/3 and make 2 50' cords and put some ends on it, then I should be good to go. Also has anyone had a custom canvas cover made for their MEP?

Adjusted set as close as I could to the upper limit of 63Hz, been running my desktop and window AC on it hangs around 50%. The UPS on my computer does kick in when the AC compressor kicks in. Might help if I used a heavier extension cord using a 50 foot 14 AWG cord. I do see a decent voltage...

Installed Kloppk's controller that he made to replace the SLC100. The controller is well worth the money bought two of them. Runs happy now, beside that noise I need to hunt down. I'm fairly sure it's the mufflers back plate came loose again doesn't make that noise till the set is warm. Kinda...