Search results

I cleaned all of the connectors, now it shifts perfectly fine up to overdrive, it won't go into overdrive until I completely step on it up to 3,000 RPMs. 1-3 gear shifts flawlessly though. I'm assuming like RWH said, the TPS, does anyone have a good explanation on how to adjust the TPS or is it...

Oddly enough, the truck is shifting perfect after I just mess with the wires at the brake pedal assembly, maybe a loose connection can cause it?

Is this the assembly that connects to the brake pedal?

Yea I have this same fan, for me it's much better than the original cadillac valve setup, especially going uphill. I know people say these engines can run hot, but these 6.5s are not no cummins or duramax, the 6.5s are well known for a high failure rate of overheating and crack blocks. I also...

For some odd reason my transmission is popping in and out of overdrive, it act as if it don't know what gear to go, the only way it won't do this is if I get up to 60Mph or really put my foot down. I've done a little research and see people say about some throttle control issue or the TCM, I'm...

Got a hose made at the local hose shop, they got me some really good high pressure fuel hose, definitely much better than the plastic hose on the truck and the hose that I got from napa to use with the ferule fittings.

I was going to write a new thread about this but I figure this would be a great place, I've been running the super singles on the M35a2 for a bit and here's the difference for me (Pros and cons) Better cruise speed 55-58Mph at 2200-2300 Rpm, much safer than the 45-48Mph on a 70Mph freeway that...

Could be 20k hard miles, my broken speedo had around 3.5k and the hours was around 300 if I remember. My transfer case and transmission looked clean but the ball joints look like they seen better days, the radiator looked like someone got in a fist fight with it, the transmission wiring harness...

Mines came with a broken speedo and ever since, I just used a GPS

Does anyone know if there's a particular way to find the actual mileage on the humvees? I'm assuming there's some sort of scan tool that be plugged into the 4l80e possibly? I'm just a bit curious to see how many mines have since I've been driving the truck a lot. My old Garmin GPS said I drove...

Cheap hose clamp and hose can cause that, I had the same issue until I use the Norma hose clamps

I'm currently on the last part of bypassing the FDC which is routing the hose from the back of the filter to the hydrualic head but for some reason, I cannot for the life of me get the hose to seal up with the fitting, sleeve, and inserts. The question I have is do anyone know if there's a pre...

I know this is a dead and beaten on topic, but has anyone yet recently swapped over to a better overdrive transmission or transfer case that's readily available? If so, please tell us what you had to do and the details to it, how much you had to cut the driveshafts, did you need to move the...

Anyone has the exact size for the driveshaft bolts that connects the rear transfer case driveshaft to the rear axle? I'm hoping I can go to the store right quick and get them instead of ordering some, I lost the original when we removed them for a tow

Well, maybe I should've adjust the steering stops, the pitman arm finally ate itself up inside and left me with no steering

Yep, the m35 has been my most useful truck so far, I just used mines this morning for a complete house clean up job, I had just enough space to fit everything that has to be dumped

I installed the 1/4 plates, I will test drive the truck later today or tomorrow to see how my right turn is, I took some measurements and even with 2inch spacers, the tires would stick out a bit pass the fenders, I will look and see if I can find some 1inch or 3/4 spacers on the market since the...

All I have to say is "What the "

Yea, it seems like my best bet would be the 2inch spacers, that would bring my wheels backspacing from 10.96 to 8.96, that should still let my wheels stay under the fender or flushed

I've finally done my homework on this, seems like the wheels to use are these: MRAP wheels with 7" back spacing 10 bolt 13.187 can fit M35A2 with adaptor plate | eBay they have 7inches of backspacing compared to the 10.9 inch of backspacing on the MRAP wheels I have on. I do have some 1/4 inch...