Search results

Not sure if anyone took this thread any further but I just ordered the following and will likely be putting it in later today. Heat reflective sound deadening foam. 1" thick 54" wide McMaster # 5692T35.

Where are the two baffles? I found one approximately 3 inches to the front (cab) of the pickup and returns. The pickup tube feels like it slides in a section in the tank at the last inch of the pickup. I think I'm getting an air bubble in the pickup due to you can here the pump loose suction and...

I know this is an old post but it relates to a question I have. Does anyone know how the tank in the A0/A1 trucks are layed out? I put a fuel pump to push fuel to the ip and its working great with the exception of being under load and taking tight turns. What I think is happening and how I am...

Steve, that is correct. So far only 3 or 4 SS members have said they are owners of the 22 possible trailers so this thread has morphed into a one stop data dump on a rather unsupported item. No tm ever made, a mix and match of hardware and although a very nice package, it is rather complex for a...

Trailer is half decked with 2x6 Oak. Still debating on whether or not to do the entire deck as it worked out well open in the middle. Tie down points are going to be welded it, we just wrapped cross members and the trailer tie down locations. The deuce weighs 11,500lbs and the winch pulled it up...

Ill have to fully read this and reply accordingly but I'm super busy. The starteri have was a 2 blot and the new one was a 2 bolt. I had to grind a little section since the block sticks out at the worst spot. Fit right in and starts great. Batteries are lawn mower batteries.

I have some 427 parts that were tanken from a rebuilt motor if you need. Good luck. The ldt427 I have had 2 heads

Give fleet filter a look. I always use them as they have great prices, fast shipping and they sell wix

Ill be floating around between trucks and my table 0-44. Plan on going up tomorrow to get some stuff up there. Also cut a few sets of Multifuel air compressor wrenches if people are looking for them and I have a 24V dump hoist kit for sale also.

Ill Bite. Likely coming up Friday afternoon if not first thing Sat 1) LiqTenExp - 1985 AMG M923 2)aheilmann68 1966 M35A2 Bobber 3)aheilmann68 1984 M923A1 4)aheilmann68 1991 M923A2 Bobber 5)aheilmann68 (friend) 1985 M931 bobber and Schutt Industries Self Loading trailer 6) 7) 8) 9) 10)

The 203 starter should be 24v and the set up in the unit was 24v to the starter. Remote worked great, new batter needed then needed to reprogram the remote. Start unit and hold the green button on the remote for 10 seconds, you only have the first 20 seconds after the hpu starts

New starter came in and started right up. Diesels are great like that, higher likely hood of starting after sitting for years. Lubed the trailer, ran the hydraulics, put a new remote battery in and reproggramed it and it was good to go. A couple of things to note I found first off the starter...

Finally got the 1CSL0-SLC-T-1000 Self loading trailer in from Rock Island and man this thing is stout and thought out. Right off the bat the batteries were dead, replace them and go to start, nothing. Took starter off and apart and its plugged solid with rust, attempted to clean it but only...

Stuff for sale: M105 landing leg in good condition Jerry can holders (10 or so) M105 master cylinder M105 bob kit (all of the suspension parts) M105 parking brake levers M35a2 wooden bows (full set) M35a2 bed cover (not in good condition) M35a2 end wall curtains (fair) M923 bows M923 bed cover...

Got the dump bed in, fuel lift pump and inline filters in.

Are there any fliers available to hang/hand out or even email out?

Great, thanks for the information. I will likely do it later in the month when I have more free time.

What o ring did you end up replacing it with, is there a cummins number or a regular diesel safe one ok? Can the shaft be accessed from the motor side of the pump or it really has to be removed? Thanks for your help

I am having the same issue with my 250, I removed the aluminum cover plate but could not get the cam to come off of the shaft. I loosened the set screw on the cam but didn't try to apply too much force to the cam for removal. Ill try again when I get some time and soak the cam with penetrating...

Does anyone want to start and official MTA Show for sale thread so we do not flood this one? I have some stuff I will be bringing up there.