Search results

I just picked up this 1984 M1009 from a police auction: VIN- 1GBED18J0EF138505 Registration- NF03AL NSN- 2320011232665 Where I bought it- police auction- Chatsworth, GA Bumper #- Left Side- 1-AE/1571NF Right Side- 1/349 16

Nice. I had planned on bidding on both of those last week, but I got caught up at work and forgot to place my bids. Lucky for you.....haha!!! Have fun with it.

I bought a complete wiring harness from hillbillyWizard.com Wasnt hard to install.

An all purpose winch that will be used maybe 10 times a year.

Im looking at buying a 9500lb winch for my m1009. Will this be enough?

Forgot to add that there is quite a bit of slack in the ebrake pedal.

I havent driven my cucv for about 2 months. Today I jumped in it and reversed out of the driveway. It backed down the driveway just fine. I put it it drive and it wouldn't move on its own. Usually once you put it in drive it will roll forward under its own power. So I give it a little throttle...

I'm selling one of my m1009. Right now it has a brand new softopper soft top installed on it. Would you guys think it would sell for more money with the soft top on, or with the original hard top?

For a constant source, I used the small open slot just to the right of the 5 amp b.o. markers fuse (as seen in the diagram below).

A couple of months back I bid on and won a 1985 m1009. I found it on govdeals and I paid a whopping total of $582. I brought it home, installed two new batteries, a starter, new glow plugs and controller, and she fired right up. I have since added new tires and have completely replaced the whole...

In addition to the harder starts over the last couple of days... I just made the 48 mile trip home from work. After starting up the truck (m1009)I let it idlefor about 20 minutes before I left work and it idled fine the whole time. I drove about 15 mileswith no issues and stopped at the gas...

I know ATF fluid is supposed be used in the np208. I noticed a small leak coming front the transfer case skid plate and it was gear lube. I guess the police department that I got the truck from put the wrong stuff in. Should I get it out ASAP and replace it with ATF? I've also go to figure out...

Thanks guys. I'm going to replace the tail pan and put in new wheel wells. I'll also be doing all new stainless brake line. It should clean up nice.

I don't think there's any Ziebarts near me. I can see where the drilled the holes around the doors and applied their rust proofing. On the frame the original undercoating has peeled off on a lot of places. I'm going to try to remove what I can then reapply more stuff.

I just picked up another m1009. I had Carnac look up the info and it apparently spent a good portion of its life in Pennsylvania. I bought from a police department near Knoxville, TN that has had it since 2004. I noticed that it had been treated by Ziebarts when it was brand new. The floor pans...

1985 CUCV M1009 VIN: 1G8ED18J9FF142800 registration: NF0AQK NSN: 2320011232665 purchased from a local police department, they claimed they received it sometime in 2002 bumper numbers have all been painted over, the only thing I can read is 79 CF Date of manufacture: 01/85 Thank you so much, I...

Thanks. I just didn't want to buy new seals if since I believe the soft top will seal up differently. Thanks again for the info!

I'm going to order a Softopper soft top on my m1009. Right now, the hard top leaks where it seals to the body. When you install the new seals for the body/top, do they get put on the actual top or the body?

I need to replace the steel fuel lines from the tank all the way to the front of my m1009. Is there any where that sells prebent lines? Would I be ok just running diesel rated rubber hoses instead of steel lines?

Bring it over to the house and we can get it done.