Search results

Ok so just went out and gave it a shot it looks like I got voltage once at the lugs but then I couldn't get it to read anything again. Another thing I noticed is as I throttle the engine it looks like the gauge is loosing voltage goers down from 120 to 100 but if I let off the throttle goes back...

Haven't checked the lugs yet I would figure the outlets should have power above everything else since they bypass a lot. I have checked some of the TM's not really sure where to start though especially since the voltage gauge is saying it has power. Sent from my SAMSUNG-SM-G890A using Tapatalk

Hey All, Recently just picked up an mep002 was kind of in rough shape but i have it running now. Voltage gauge is showing 120 but problem is when i try and plug something into the plugs i am not getting any power? Any ideas where i should start? Do you need to have the HZ gauge hooked up for it...

Awesome that's perfect thanks! Sent from my SAMSUNG-SM-G890A using Tapatalk

Ok so I took a look at the wiring diagrams I got most of it figured out but a need some verification on some things. 1. I believe the smaller gauge wire is for the starter solenoid control. 2. The 2 other thicker wires I believe are both for the stator? Is one a ground and one a positive...

Can't see wire numbers I took a look at the tms briefly maybe I just missed the wiring diagrams Sent from my SAMSUNG-SM-G890A using Tapatalk

Hey all, Just recently picked up an mep002a. Wondering if anyone knows what these 3 wires are for? I assume 2 go to the starter but can someone pinpoint me which one goes where? Also how do the fuel pumps ground I have a positive but no negative or looks like does it just ground by the mounts...

Hey Guys, Not sure if its an issue or not but I get gray smoke at idle whether warm or cold doesn't change doesn't go away. When i accelerate or move it turns to black/brown which i know is normal. Is the smoke at idle normal or something wrong i don't recall it normally doing this? Notes: I do...

Hi Trying to get my non turbo deuce turbo'd. Quick question is my clean air kit did not come with the airfilter to turbo intake tube do i need to by one or is there some way to use the old parts to connect to turbo? Also does anyone have an instruction manual? Thanks, Mitch

Hey all, Wondering if anyone on here has tried / been successful with making a inexpensive gun ring for the m35a2? Would love to see pictures / designs of anyone has them! Thanks, Mitch Sent from my SAMSUNG-SM-G890A using Tapatalk

Hey All so I finally got down to figuring out what the issue was looks like I had some left over gasket material on the input shaft Input Hub (the whole assembly with the shaft seal) causing it to have space between the front bearing allowing the whole shaft to move back and forth a little. I...

So today tonight i had some time to try to inspect what is going on which didn't lead to much conclusion....I pulled the floor up and drove around a little bit and it seems that maybe the case is moving but it was very hard to tell. The only time I saw the shifter shaft move was when i held the...

So if its not the entire case moving around what would it be? If I continued moving around with my old mounts would it damage anything? Thanks, Mitch

Hey All, So I just went through the process of rebuilding the transfer case recently on an m35a2. Got everything back together and have been driving around I notice the gear lever moves around in high range while driving (when I decelerate / bounce around). Its not popping out of gear or making...

Hi All, I am rebuilding the input shaft gear bearings on my m35a2 and just want to be sure i install them back correctly. When installing them do the bearing shields all face toward the back of the input shaft or do they face the inside of the gear? Thanks, Mitch

Hey All, Started rebuilding my transfer case after a both bearings on low gear decided to spit out all the ball bearings. Question is on doing this it appears to have demolished the spacer that goes between the low gear and bearing and I can't seem to find anywhere to purchase itaua #15 shown in...

Thanks All!

Hey All, I am getting ready to flip my hubs to put some super singles on and have a few questions that I couldn't seem to find when looking through the TM's. 1. I am new to the split wheel / locking rim type wheel do i need to deflate before i remove from truck or is it safe to remove from truck...