Search results

O ya take care ob the business side very Cool.

Well if you dont need to weld all of it & need to remove it later I would use 3/8 Poliy carb & paint it cut with saw will look real but light. When we UP armor M1070 Het in 2004 we used 10mm ar400 b plate & bolted to the door's with spacers & renforce plate on soft shell side. some of where...

Cool M1009 Like Winch & Claymore. Head liner look's good to. Great job over all 1 thru 10 I vote an 10.

Yes I on look out for an CUCV door data plate for M1028A2 my old 86 driver door was hit & some one scraped the door out befor I could remove it to reinstall on the new door. Great help Thank You. C J T

sounds like the rubber o ring that seals the sending unit could be dryed out or flat out gone take look at that Than happend to me on V1991 5/4 UV5 same Tank street side.

If it is fuel sel Just have the pump recon. And replace the front grank seal & gaskets & water pump all at the same time this will further any other problems. & return lines & all rubber lines Inspect every thing. my CUCV M1009 runs great & M1028A2 will burn the tires off. When in IRAQ we only...

Royl Oak for me went north Flint & so on.

I see the 6.2l 6.5 l they are easy to work on I worked on them Level 10, 20 , 30 ti maint. Through DS Maint. The ARMY way ckeck all your fuel lines filter base return lines ar very importing to. But it sound like an fuel sel. :jumpin:

Hi hummer4x4guy have my M1028A2 will be Mission Capable get me more info asap.:jumpin:

Man it sound great but I should be on convoy to New Mexico in october military invite only to train New HET Operators 6 week opp in the box.:driver:

Hi on engine cut off here is one way to check inj pump fuel shut off get light & wire hook up tp the pink wire at inj pump use push pull spade auto parts have them wire an extra line to it & ground the light make wires long enought to bring light inside cab if or when the light goes out & the...

O ya M,L jeep look good in the mud hole :jumpin::jumpin::jumpin::jumpin: here comes CUCV cummins.

Just jumping on bord The 4L80E is Great for Gaser but the Cummins B or C you will take main shaft out and or tork converter will blow out there is no way to set the trans to control Tork limits limiter gaser bulid tork with rpm Diesel build with BOOST I run 6BTAA 259HP at the crankshaft &...

NP203 has to be in gear when starting out :driver:for hwy. this system is like have two speed rears.:beer:

Hay that sound good where will be at need more intel.

Hello There when will they re up new date of show.

Hi the 203 is gear set is reversed & it is now an over drive unit this is also used in quad plexing transmission in semis rigs I had 1 W900b KW & fliped the ladt two gears and wow la OD was in works an good transmission shop or old timer that builds them will be the man for the job. All it call...

Hi the 4l80e can be installed right to the T case the rear trans out put shaft eill half to be pulled out and install shaft that stick out 4.500 in out the rear of the trans where it bolts to the trans for the np205 to work the 4L80E is aprox 1.750 in longer than TH400 trans 32 splin out put...

Maby my m1028a2 might be done by then still up in the air. I just set an Cummins 6BTA in line 6 cyl in it built new trans TH 475 & NP205 with lomax gear set in it Installed 1410 yoke u jonits & 4in od prop shaft & hd spline slip joint. removed GM 14bolt 4.56 replaced with Dana 70 hd 3.07 gear...

Count me back to the Bricks in Flint , Mi . In to both of M1009 & M1028a2 My m1009 is in maint. full resto frame off sa DS maint. My M1028 power By 6BTA Cummins out AF TUG.:p