Search results

TWM - here is a pic of the tool. It accomodates blades up to 4 inches long - at that length you have to be patient and cut slower - this baby cranks and cuts as you can tell how slick that hub I cut was - at the center of that hub it was 3 inches deep. Of course my saw does not have the...

New windshields cut and ready to install - new windsheld seal and ribbon ordered. New right rear hub-seals-bearings ordered for Dingers jeep New knuckle upper and lower king pin/spindle bearings ordered for both sides _he has to order the seal kits yet. New shock coming in for both jeeps along...

There goes my parking areaauaaua

I think its named Silkaflex - tube you can use in your caulk gun - made for this problem for scuffing. Try HD or Lowes. Trying to remember the product # but I think it is 215. Black tube - works wonders like a silicone but better. I use this on semi trailers ribs and skin.

Hey DW - Sea Foam makes a great product to put in with your fluid to help clean the valve and system - also a good pre fluid change flush thought here !! FWIW

Have a lot of little things to do before placing parts on - hammered some more on the fuel tanks before it warmed up outside - then opened the garage door and played with little parts. I moved the tanks so you could not peek at them - pics coming later once done. DH probably remembers what...

Stalker :ditto::ditto::ditto:on the awesome one clean looking 109 you have. Less time working on getting the body repaired and more time to play with the box how you want it. Welcome to the M109 CLUB. See ya at the Ga Rally with that unit congrats.

Welcome aboard 760 you will find lots of assistance here once you get one - spend a little time aquiring the TM's and searching for info already posted = more a less get a heads up on what you will be getting.

SR - I bought them from DH - paid for the transportation down here and gave one to Dinger and the other to my wife. I am going through my wife's (one that was blue) and helping Dinger with whatever help I may be able to provide him in getting his going and rebuilt. Gotta get em done so I can...

I am just about a mile and 1/2 North of HWY 78 up Killian hill

Tigger - I hope you bring your jeep as well - that way I can see one the way it us suppose to look like and how bad I screwed up :beer:

PB had to finally come over and ask what I was using as firewood as I obviously did not have a stash of it (some folks brought truckloads of it) and I had to tell em those brown round big chips laying on the ground fired up really nice once the fire was started with a little gasoline :arrow...

That right rear wheel hub - I had the three leg pulled and it would still not budge even red hot. I used my air saw and cut through to the keyway - put the puller back on it - heated it again with just a little load on it and about 7 minutes later it came flying off. You can see on the...

See if Joint CLutch & Gear is still in Grand Rapids up there for parts.

You made a great statement above ^^^^ politially correct people. I kind of doubt most have a preference on any vehicle even be it an MV. They just know one thing - and that is how to do it the DMV way - enough on that one. The more correct detailed information you can bring them in...

Hey Bulldog4 - welcome aboard. Check around and you will find a lot of runs you can head to this year w/MV or without. Go to the main page on the forum at the bottom and check out the 2011 Ga Rally info and start planning NOW. I have a non run - get together with whomever wants to come at...

Actually I dislike cold - but it keeps me in the garage working on MV project more and with more intincity - cause when I am done I have to walk back to the house in the cold - so I stay longer. The Bigger projects seem to get done - cause if the doors were open I would be day dreaming and...

Hail DH - puters are a great thing when you are behind the scene (not so good when you are the one getting spanked or banned rofl)

Here is a goor part J <Keep It Clean with Puradyn>

bout another week of my spare time pounding metal and I will have your pics - they might not be up to your par of proffessionalism in metal bending - but don't think you'll be disappointed either. Spare time I have to look for a right rear axle hub for Dingers chassis.