Search results

Took time out from his day to get me a pic and measurement off the floor of what the clutch peddle floor board stop plate looks like on the M37. Mine was missing. My name is not Smith and I doubt I could shoe a horse but a little heat and a little bendy bendy and looks good enough to me. It...

Freezer bag not freezer they are thicker I believe and won't rip getting that nasty grease on you hands. Myself I like the way the grease makes my hands smell and oh so soft.

Talk about hens teeth but I found the last battery tray for sale on Earth I think. Little new paint on the bottom and tomorrow a little new paint on the top side, dry and install. Ordered the battery hold down bracket and should be here soon and thanks to one of our members post two 1993 Honda...

I did not think of it causing a panic and I did not think it would but I did carry protection. I am trying to get my other property cleaned off so I can sell it so yesterday I fired up the 915 and hooked to my 373 trailer. Loaded the trailer up with most all my storage boxes and came straight...

Brutacus pretty cool you found the front drive flange makes a good seal installer. As you said it does not hit the rubber and hits the metal edge. You were right and that is the main thing as the seal installers in the other post would not work as it would be crushing / pushing on the rubber...

The seal drivers in post #54 will not work . I took my CR seal driver tool and added the ring and yea I have the handle. Also you do not put grease on the seal edge if that is what you are talking about. You can clean the mating service of the hub with some light emery paper to get it clean...

Welcome and looks like you first lesson was a good one. Also your Rockwell's might not have lockers but some MV's do. I do not know if they would have helped you out here. Anything can get stuck so carry a push rod and check the depth to the bottom if there is one.

Yea saw the same problem with the 5 ton hub seals long ago. Called CR and asked if they had the correct seal installer tool and they said no. I had this one made up by adding a ring of steel around the edge that lines up ok with the inner ring . Most seal installer tools put the pressure around...

Nice.

Yea I just ordered the whole kit and now I see what just the rubber hose did. The hose just runs from the fitting and up just the wire that goes under and up the inner fender to the electric connection. Would say it is there to protect the wire from shorting out and cause the horn to go off /...

Good call on the drive line. Mine was out of phase on the front shaft. Believe someone removed mine for some reason and pulled it apart and stuck it back together three splines off. Nice job someone but next time you do not have to pull them apart like you did and then put it back in the truck...

Nothing like a soft top. To tell you the truth any windshield that can be folded I love a soft top. On the Deuce or 809 series so much easer to pull it off and do transmission a R&R and the safety factor than working from the bottom. Still waiting on my antique tag but took it for a ride on my...

No there is not a copper gasket or O ring on the top of the head hex plug. One on the delivery valve.

No seal there no copper washer no O ring . You can try and remove it and polish both the head and the plug contour with one of those 3M ultrafine pads. Then before install of the plug turn on in tank pump and fuel will come out and push any trash out of threaded hole. Put the plug in maybe with...

Once again thanks to Harlen. Got the correct size belt for the alternator up grade and she again is charging. Put the maxi fuse holder in and waiting on my tags.

Pressures are a good thing to check when there is a performance problem . Thing is a Deuce will idle with the pressure relief valve wide open as it has been proven. There is another way to check if the main fuel control is set to low . You need a helper to hit the starter button or a remote...

Since your FDC is bypassed all fuel control is now adjusted by way of the main fuel control or the twin nuts. Myself when adjusting the twin nuts is use a black magic marker on one of the flats so I know how far or how many turns I have adjusted it. If you idle screw has not helped with...

Rear drive shaft front u joint was bad so got it replaced. Went to put some grease in the rear drive shaft rear joint before I installed the drive line and Thanks. Someone put the u joint in backwards and they must have said heck with it as the grease fitting not even installed. If you put them...

At the end of the steering box where the horn wire comes out there was just a little piece of rubber hose there. How far did it run up the inner fender well? seems like it would only have been able to go half way up the inner firewall to the electric connection. I would think it was for fording...

Yea the No Spin in the front with Overson hubs and air lockers in the rears or if they make a locker for the rear axles that is more forgiving than the No Spin. The 816's I left as is ( not bobbed ) both rears and both with No Spins did one heck of a job in the local mud pit called Hogwaller...