• Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!

  • Microsoft MSN, Live, Hotmail, Outlook email users may not be receiving emails. We are working to resolve this issue. Please add support@steelsoldiers.com to your trusted contacts.

 

Search results

  1. schwenk industries

    NV4500 Swap with part numbers

    Never heard about the diffrent nose cones, that's intresting I would have figured they are all the same. It did not bother me grinding it out seeing as it is below the block where the bell mounts anyways. I will be finnishing this swap up I hate when threads are left unfinnished. I have had a...
  2. schwenk industries

    bad 14 bolt

    Rear 14 bolts are fairly common like was said the front is where the money is at. I second the bearing cage, I found one of those ground up at the bottom of my NP208. The front axle I would'nt think would be a Limited slip.
  3. schwenk industries

    NV4500 Swap with part numbers

    Now that the bellhousing is preped and has good clearance around the starter, the bellcrank bracket has been test fitted. We'll install the flywheel and clutch set. I used a single mass stock 12” 6.2 flywheel Napa # NCF 88201 The original Flex plate bolts are not long enough and the head is to...
  4. schwenk industries

    NV4500 Swap with part numbers

    No we're not done with the bellhousing yet! You should know you can't buy anything that just works like it's supposed to. The AA Linkage bracket #715534 Dosn't really just bolt up to their own bellhousing. Where the main bracket bolts down the lower hole is 3/16' away from the bell casting. If...
  5. schwenk industries

    NV4500 Swap with part numbers

    The bellhousing as stated is an Advanced Adapters #712577 with the bell crank bracket #715534 that you need because the side of the bellhousing is not tapped for the bellcrank stud. Every thread I have read about doing NV swaps people say “yea you gotta use the AA bellhousing” that's about all...
  6. schwenk industries

    NV4500 Swap with part numbers

    Sadly I already installed the pedals before I got the idea to record all this so there are no pictures of it going in. Ideally you won't be a Hack and you will pick up a manual steering column when your at the yard. I'ma hack and used the auto column anyways. I don't remember why I punched one...
  7. schwenk industries

    NV4500 Swap with part numbers

    So a few weeks after I bought my M1009 the TH400 took a crap. I figured no better time to swap to a NV4500. I searched SS here and about every other forum about trucks and off-roading I could find. Could not find a detailed write up about any modifications or part numbers needed to complete the...
  8. schwenk industries

    NP208 Trashed Thrust bearing!

    ATF only Per TM / GM I Figured It was strange as well that's why I posted it. I Might pick up a parts unit I will have a parts TH400 maybe someone Will trade.. I can hope anyways.
  9. schwenk industries

    NP208 Trashed Thrust bearing!

    yep when a bearing spun on a shaft stack up a couple TIG beads and turn it back down, we didn't have any spray welding equipment unfortunately. I just don't want to affect any heat treatment that may have been done to the gear or splines, come to think of it I never checked if any of those...
  10. schwenk industries

    NP208 Trashed Thrust bearing!

    The bench is stacked high to the left with other parts, I keep that 1/4 of the bench clean for projects. Being a Machinist and also a mechanic I have a little bit of the Keep things clean and orderly, I wish I never had piles of parts but I just don't have enough room to keep everything as...
  11. schwenk industries

    NP208 Trashed Thrust bearing!

    I won't go into great detail about the story I will save that for the NV4500/M1009 Swap thread. If there is interest? (I did not want to fill that up with this question/Info) So after removing my NP208 for my trans swap. I pulled it apart to inspect bearings, gears and replace the seals and...
  12. schwenk industries

    Split shift transfer lever extension

    I was debating removing the bench in my m35a2 and running two spring seats. That way I can make a whole new t-case shift leaver that come's straight up so it dose not have the bend in it like stock. That way you don't have to bend at all or look for the leaver. I'll say this is definitely an...
  13. schwenk industries

    Vacuum Regulator Valve Fitting?

    Thank you gentleman. That's what I had figured, wasn't sure what the little part on the side was for.
  14. schwenk industries

    Vacuum Regulator Valve Fitting?

    The TH400 in my M1009 took a crap, I plan on putting a Nv4500 in its place but due to a lack of funds and me needing my truck I'm attempting to get it fixed. So far I’ve only replaced filter and fluid, vacuum tested the modulator valve and found this little rubber fitting on the vacuum regulator...
  15. schwenk industries

    Register M51a2 In IL?

    I am interested in buying A M51a2 But I have no clue as to how I would register/ insure this truck? I don’t own a farm or business so I can’t use that as a way to register it. I don’t have a CDL but it can sit somewhere until I get a CDL, I have looked on the IL DMV site and do not see how I...
  16. schwenk industries

    M35 Alternative Transmissions?

    well I did now about the split shifting with the t-case but was looking at potential ideas, I am now getting the time and funds again to maybe jump into this hobby and find a Deuce but was looking at potential things to tinker with. I am not fond of racing the engine only to achieve 55MPH Don't...
  17. schwenk industries

    M35 Alternative Transmissions?

    It is good to be back on the site I have been much to busy and have finely gotten time to get back here. I am just wondering If anybody has thought of putting a alternative transmission or auxiliary box into the M35. Either more gears for more hill/load pulling choices instead of the large gaps...
  18. schwenk industries

    M35A2 As a working Truck

    Since it seems no one ever posts this anymore I will share this bit of info. It contains information on the M44 (M35) series trucks. Welcome to the site, and don't worry if some of these boys get a little grumpy and say some strange things that you may take as being mean but they all mean well...
  19. schwenk industries

    M35A2 As a working Truck

    Since it seems no one ever posts this anymore I will share this bit of info. It contains information on the M44 (M35) series trucks. Welcome to the site, and don't worry if some of these boys get a little grumpy and say some strange things that you may take as being mean but they all mean well...
  20. schwenk industries

    New Member in Texas

    I don't think the file worked??? oops guess it did. sorry.
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website like our supporting vendors. Their ads help keep Steel Soldiers going. Please consider disabling your ad blockers for the site. Thanks!

I've Disabled AdBlock
No Thanks