Search results

I have a Davey 7MC2-A compressor that I purchased from GL. I had hoped to use it for sandblasting. I worked on it and got the Hatz 2G30 engine running. The compressor will only produce about 50 PSI. Do any of you know anything about this compressor or where I can get parts. Davey closed...

I have a Davey 7MC2-A compressor that I purchased from GL. I had hoped to use it for sandblasting. I worked on it and got the Hatz 2G30 engine running. The compressor will only produce about 50 PSI. Do any of you know anything about this compressor or where I can get parts. Davey closed...

They still are available on GL. They go for as little as $150 plus 10% and taxes. And as much as $250 or so. Ebay about $450. Location has a lot to do with the price. The M101's go for more because they are better behind a pickup. Every M35 needs an M105.

I replaced the o-rings in the master cylinder of my M35A3C, yesterday. The correct o-rings are dash 222 not dash 129. The dash 222 has a larger cross section than the dash 129. Just a note: The valves in the top part of the schematic have small springs under them. Be carful during...

This is a schematic of the master cylinder from the G503 site: I wish that I had the full schematic. It looks like the pieces that are circled hold the pistons in place and prevent them from coming out. They must be lifted up along with a pin near the center to allow the pistons to be...

The o-rings that I believe are the right ones are Dash 129 EPDM O-Ring AS568A from McMaster-Carr, part number 9557K163. A pack of 50 for $10.46. I will let you know for sure when I take mine apart. It wouldn't be the first time that I had one size off of what I needed. I have gotten quite...

I have the O-rings but haven't had time to pull the master cylinder. I hope to pull it within the next couple of weeks. I'm let you know what I find out.

The TM's call for new locknuts to be used every time the wheel is broken down. I have searched the post and I can't find any one that referred to replacing them. O-rings and grommets are replaced, but not locknuts. What do you say about the need to replace the locknuts? I assume that this...

24v bulbs I found a source for 24v bulbs. I now buy 10 packs of bulbs for less than I was paying each. The website is 1000bulbs.com. Just search for the bulb number. I ordered a package of each bulb that I might encounter for my vehicles and trailers and put them into my "crash kit" for...

M35A3 Master Cylinder rebuild This link covers the MC issue and some problems and possible solutions. http://www.g503.com/forums/viewtopic.php?f=26&t=177512

I too am having problems with an M35A3 MC in need of repair. I did a search and found a thread on another website. He had trouble finding a replacement. He rebuilt the MC. He said that it doesn't have cups like other MC's and uses 3 O-rings. He honed the cylinder and used EPDM O-rings that...

Has anyone found a solution for stowing a spare in the standard location? I saw that YOUNG GUN had a spare in his pictures. Is it a 14.5 R 20 or will a 395/85 R 20 fit? What are the ramifications of running a different size tire to get back home?

air leak I have two A3's and had the same problem on both. I replaced the push in air tube fittings and it fixed the problem. There are two fittings on the air switch. All of mine were John Guest plastic fittings. They are available from McMaster-Carr. Each valve has one straight and one 90...

I have an M35A3 that has numerous John Guest plastic air fittings. I have tried to remove several that were installed into brass fittings and they break off each time. They were apparently installed with pipe dope. The plastic that is left is tougher than I thought and I can't get it out without...

Steve, As long as my EUC comes through this week, my plan is to head to Gulfport on Sunday and pick up my Deuce on Monday. Call me if you would like to travel together. Dale 678 313 7645

I am making a trip from the Atlanta area to Gulfport, MS for a pickup, a pickup at Eglin AFB and return to Atlanta the week of 6/18/12. I plan to pick up an M35A3C in Gulfport. If I could help pickup or deliver, I'm available. Assistance along the way in case things don't work as planned would...

I have an M35A3 that has not had a problem with the turn signals until just recently. The front signals operate correctly, but the rears seem to be "out of phase" with the lever. When the lever is turned to the right turn position the rear goes into flasher mode. The right, left, and flasher...

M832 Dolly I don't believe that an EUC is required for your dolly. I have 10 days to get mine, no EUC required.

When I picked up my M35A3 at Ft. Riley, all six tires were flat and the CTIS system had been left on. I tried to use the system to help inflate the tires to no avail. I inflated all tires to 20 PSI and the CTIS still reported flat tire. I gave up on it, turned it off, filled the tires, and...

Thanks, I updated the onfo. Dale