AMMPS Generator Series Remote Data

kloppk · Dec 20, 2023

ilajnfae said:
... Kloppk, I'm very interested hear what data the ECM replies with from a running system when you get a chance, ...

I have a 1030 so it doesn't have an ECM. The 1060's and up have an ECM and the DCS talks to them over CAN.

ilajnfae · Dec 20, 2023

Ah... fair enough, thanks for clarifying

R1ckyb0nd · Dec 20, 2023

ilajnfae said:
I have a CAN to USB adapter from Gridconnect, PN GC-CAN-USB IPEH 002021. I'm also using a 30 day trial of their PCAN-EXPLORER 6. My 485-USB is just one I had laying around from an old security system install, no PN visible. Kloppk, I'm very interested hear what data the ECM replies with from a running system when you get a chance, the DCS sends the same 3 or 4 messages over and over, but anytime I try to inject what seems like a reasonable value (coolant temp, RPM, etc. ) The DCS declares fault 781 and fusses about a reply rate, lol. R1cky, I'm about to go pull the DCS off the full harness and see how the 485 works

That is an expensive can to USB, from your message it looks like you are able to get some, if only the same 3/4 messages, from the CAN bus?
Do you know what the CAN baud rate is? I have tried my jetson Nano, and Arduino Uno, and nothing is getting any bus data. The adaptor I have has a 800MHZ crystal, so it can only do 500K CAN bus speed. I wonder if this is the issue.

ilajnfae · Dec 20, 2023

R1ckyb0nd said:
That is an expensive can to USB, from your message it looks like you are able to get some, if only the same 3/4 messages, from the CAN bus?
Do you know what the CAN baud rate is? I have tried my jetson Nano, and Arduino Uno, and nothing is getting any bus data. The adaptor I have has a 800MHZ crystal, so it can only do 500K CAN bus speed. I wonder if this is the issue.

Based on the oscilloscope rate of 4 microseconds per bit, I chose 250kHz and it seems to be happy with that

kloppk · Dec 20, 2023

Icesythe7 said:

Code:

GenSet Voltage L1-L2 = 12 2
GenSet Voltage L2-L3 = 13 2
GenSet Voltage L3-L1 = 14 2
Bus Voltage L1-L2 = 14 37
Bus Voltage L2-L3 = 3C 37
Bus Voltage L3-L1 = 64 37
GenSet Voltage L1N = unknown
GenSet Voltage L2N = unknown
GenSet Voltage L3N = unknown
Bus Voltage L1N = 16 37
Bus Voltage L2N = unknown
Bus Voltage L3N = unknown

GenSet L1 Current = 92 3A
GenSet L2 Current = 93 3A
GenSet L3 Current = 94 3A
GenSet Frequency = A8 37
Bus Frequency = F8 36
Power = 49 38
Fuel Level = 28 28
Battery Voltage = D1 B
Battery Current = 7F C
Oil Pressure = 8 2
Coolant Temperature = A9 D
GenSet Hours = 56 2

What I have as of today.
Will try and mess with the engine code DIP switch tomorrow to try and detect it's codes

PC	Code	Parameter
6	4	??
7F	C	Battery Current
D1	B	BatteryVoltage
88	17	??
B1	28	??
5B	0	Battleshort
A9	D	CoolantTemp
46	48	FaultCode
45	48	WarningNumber
44	48	??
E8	1	Battleshort
28	28	FuelLevel
F8	36	BusFrequency?
14	37	BusL1-L2
16	37	BusL1-N
3C	37	BusL2-L3
3E	37	BusL2-N
64	37	BusL3-L1
66	37	BusL3-N
8A	11	??
67	10	Contactor State 0=Open, 1=Closed
A8	37	GensetFreq
92	3A	L1Current
12	2	GensetL1-L2
F	2	GensetL1-N
93	3A	L2Current
13	2	GensetL2-L3
10	2	GensetL2-N
94	3A	L3Current
14	2	GensetL3-L1
11	2	GensetL3-N
56	2	EngineHours
8F	1	Battleshort
49	38	Power
9C	2C	??
62	29	??
66	29	??
8	2	OilPressure
89	11	Reconnect 2=120/240, 3=120, 0=208 ?? Need to recheck this
6A	20	??
EC	1	??
4F	10	??
6B	20	??
8E	1	??

R1ckyb0nd · Dec 21, 2023

ilajnfae said:
Based on the oscilloscope rate of 4 microseconds per bit, I chose 250kHz and it seems to be happy with that

I do not have an scope. When I connect a multimeter, I get 3.3~ volts across K to ground and 1.75V L to ground. These voltage never seem to change.
You mentioned doing something to send Canbus data. What else other than connecting k and l to send Canbus?

ilajnfae · Dec 21, 2023

Good afternoon, sorry for the delay. So if you have a ground on J3-LL, your DCS should think that it is connected to a 30 kW, 120/208 VAC, 60 Hz system. Is that accurate? I've just put a meter across J3-K and J3-L, and can confirm that I see approximately the same results. My interpretation would be that because meters can only create an average for very fast signals (like 250 kHz), that you are in fact seeing activity on the CAN bus. I'm not familiar with the equipment you are using to try to pull data off, but I'm reasonably confident that the unit is transmitting on the bus. Let me know how else I can help!

R1ckyb0nd · Dec 28, 2023

ilajnfae said:
Good afternoon, sorry for the delay. So if you have a ground on J3-LL, your DCS should think that it is connected to a 30 kW, 120/208 VAC, 60 Hz system. Is that accurate? I've just put a meter across J3-K and J3-L, and can confirm that I see approximately the same results. My interpretation would be that because meters can only create an average for very fast signals (like 250 kHz), that you are in fact seeing activity on the CAN bus. I'm not familiar with the equipment you are using to try to pull data off, but I'm reasonably confident that the unit is transmitting on the bus. Let me know how else I can help!

Are you just connecting CAN H to K and CAN low to L? are you connecting grounds to the CAN signals? I am only getting error frames when connected and I know my CAN reading Hardware is setup correctly as I now have multiple hardware setups and can pass CAN data between them, just not the DCS.

Where did you get the 30 trial of PCAN explorer? I do not see a way to download it?

Finally, Got some CAN BUS data.. now to get this working on Linux and not windows.

I am also only getting four Ids,

0xC0000DC	Data Frame	Extend Frame	4	0X\|19 00 00 00	Success
0x18F001DC	Data Frame	Extend Frame	7	0X\|00 00 00 10 00 00 00	Success
0x18FEF1DC	Data Frame	Extend Frame	8	0X\|FF FF FF FF FF FF FF 00	Success
0x18DF00DC	Data Frame	Extend Frame	8	0X\|3F FF FF FF FF FF FF FF	Success

I will try to get to the generator soon and connect everything up and see what I can get. I would like to go through the diag port near the ECU.

Reading up on J1939 we may need a DBC file to decode these, as there are offset and salting going on.

Thank you,

Rick

ilajnfae · Jan 4, 2024

R1ckyb0nd said:
Are you just connecting CAN H to K and CAN low to L? are you connecting grounds to the CAN signals? I am only getting error frames when connected and I know my CAN reading Hardware is setup correctly as I now have multiple hardware setups and can pass CAN data between them, just not the DCS.

Where did you get the 30 trial of PCAN explorer? I do not see a way to download it?

Finally, Got some CAN BUS data.. now to get this working on Linux and not windows.

I am also only getting four Ids,

0xC0000DC Data Frame Extend Frame 4 0X|19 00 00 00 Success
0x18F001DC Data Frame Extend Frame 7 0X|00 00 00 10 00 00 00 Success
0x18FEF1DC Data Frame Extend Frame 8 0X|FF FF FF FF FF FF FF 00 Success
0x18DF00DC Data Frame Extend Frame 8 0X|3F FF FF FF FF FF FF FF Success

I will try to get to the generator soon and connect everything up and see what I can get. I would like to go through the diag port near the ECU.

Reading up on J1939 we may need a DBC file to decode these, as there are offset and salting going on.

Thank you,

Rick

Good morning! Sorry for the delay. Can confirm that those are the main words I see as well. I also get retransmit requests when I switch my ENG ID in and out of modes that use CANbus, just before it declares degraded CAN bus. Does your capture give you any information about how often each of those occurs?

R1ckyb0nd · Jan 4, 2024

ilajnfae said:
Good morning! Sorry for the delay. Can confirm that those are the main words I see as well. I also get retransmit requests when I switch my ENG ID in and out of modes that use CANbus, just before it declares degraded CAN bus. Does your capture give you any information about how often each of those occurs?

Yesterday, I was able to get to a running generator and got a lot more information. I have been looking into decoding this information and it seems like some might match SAE 1939 specs and some the math is off or there is no data in the SPN where I know something should be.

18DF00DC	DF00	57088	Stop Start Broadcast
18EAFFFE	EAFF	60159	ISO Request
18EBFF00	EBFF	60415	"ISO Transport Protocol, Data T
18ECFF00	ECFF	60671	Transport Protocol - Connection
18EEFF00	EEFF	61183	ISO Address Claim
18EEFF0F	EEFF	61183	ISO Address Claim
18F001DC	F001	61441	Electronic Brake Controller 1
18F00100	F001	61441	Electronic Brake Controller 1
0CF00300	F003	61443	Electronic Engine Controller 2
0CF00400	F004	61444	Electronic Engine Controller 1
0CFD9200	FD92	64914	Engine Operating Information
18FDCA00	FDCA	64970	Intermediate Speed Control
18FEBD00	FEBD	65213	Fan Drive #1
18FECA00	FECA	65226	Active Diagnostic Trouble Codes
18FEDF00	FEDF	65247	Electronic Engine Controller 3
18FEE400	FEE4	65252	Shutdown
18FEEE00	FEEE	65262	Engine Temperature 1
18FEEF00	FEEF	65263	Engine Fluid Level/Pressure 1
18FEF000	FEF0	65264	Power Takeoff Information
18FEF1DC	FEF1	65265	Cruise Control/Vehicle Speed 1
18FEF100	FEF1	65265	Cruise Control/Vehicle Speed 1
18FEF200	FEF2	65266	Fuel Economy (Liquid)
18FEF500	FEF5	65269	Ambient Conditions
18FEF600	FEF6	65270	Intake/Exhaust Conditions 1
18FEF700	FEF7	65271	Vehicle Electrical Power 1
18FEFF00	FEFF	65279	Operator indicators

R1ckyb0nd · Jan 4, 2024

Also I have been trying to mimic @kloppk and @Icesythe7 code for getting the serial connection on the front to work but I am not getting the handshake correct.

ilajnfae · Jan 4, 2024

R1ckyb0nd said:
Yesterday, I was able to get to a running generator and got a lot more information. I have been looking into decoding this information and it seems like some might match SAE 1939 specs and some the math is off or there is no data in the SPN where I know something should be.

18DF00DC DF00
57088
Stop Start Broadcast
18EAFFFE EAFF
60159
ISO Request
18EBFF00 EBFF
60415
"ISO Transport Protocol, Data T
18ECFF00 ECFF
60671
Transport Protocol - Connection
18EEFF00 EEFF
61183
ISO Address Claim
18EEFF0F EEFF
61183
ISO Address Claim
18F001DC F001
61441
Electronic Brake Controller 1
18F00100 F001
61441
Electronic Brake Controller 1
0CF00300 F003
61443
Electronic Engine Controller 2
0CF00400 F004
61444
Electronic Engine Controller 1
0CFD9200 FD92
64914
Engine Operating Information
18FDCA00 FDCA
64970
Intermediate Speed Control
18FEBD00 FEBD
65213
Fan Drive #1
18FECA00 FECA
65226
Active Diagnostic Trouble Codes
18FEDF00 FEDF
65247
Electronic Engine Controller 3
18FEE400 FEE4
65252
Shutdown
18FEEE00 FEEE
65262
Engine Temperature 1
18FEEF00 FEEF
65263
Engine Fluid Level/Pressure 1
18FEF000 FEF0
65264
Power Takeoff Information
18FEF1DC FEF1
65265
Cruise Control/Vehicle Speed 1
18FEF100 FEF1
65265
Cruise Control/Vehicle Speed 1
18FEF200 FEF2
65266
Fuel Economy (Liquid)
18FEF500 FEF5
65269
Ambient Conditions
18FEF600 FEF6
65270
Intake/Exhaust Conditions 1
18FEF700 FEF7
65271
Vehicle Electrical Power 1
18FEFF00 FEFF
65279
Operator indicators

Congratulations! That is SPECTACULAR! I'm so jealous you have a running generator you can vampire into! I have the full 1939 spec, so I'll see what I can do about generating some of these words with values and fire them into the datastream through the PCAN-Explorer!

kloppk · Jan 4, 2024

What I found was the handshake to establish communications thru the remote port seems to use/need minimum delays between sending each of the handshake messages to the DCS. The delays are what I measured using a PC with the Remote Monitor software doing the handshaking and an ESP32 sniffing the communications and measuring the individual delays between the 248 messages.
I added say 10% to each delay for buffer in the table below. Using the delays in the table I was able to complete the handshaking and start requests and get the 44 parameters back from the DCS. It works OK for a period of time and then seems to stop getting parameters. Just another bug to solve.

I found I could ignore all DCS responses during the handshaking. With my 1030 the DCS responses were always the same during handshaking. Not sure what's in all the DCS responses during handshaking mean. Responses varied from 3 bytes to about 93 bytes in length.

Here is a table showing what I got to work for handshaking for the delays between messages.
To read the table....
Send handshake message 0 then wait at lease 254 milliseconds before sending handshake 1.
Send handshake message 1 then wait at lease 236 milliseconds before sending handshake 2.
When done wait 1 second before requesting the parameters from the DCS.

0	254
1	236
2	240
3	93
4	391
5	58
6	8
7	7
8	72
9	8
10	8
11	33
12	8
13	7
14	8
15	8
16	33
17	33
18	33
19	33
20	8
21	8
22	33
23	33
24	11
25	53
26	8
27	33
28	8
29	8
30	8
31	33
32	8
33	8
34	11
35	48
36	8
37	8
38	8
39	8
40	12
41	48
42	8
43	8
44	33
45	8
46	8
47	8
48	8
49	8
50	8
51	8
52	21
53	21
54	21
55	21
56	20
57	7
58	8
59	8
60	8
61	8
62	7
63	8
64	8
65	8
66	8
67	8
68	8
69	8
70	21
71	21
72	21
73	20
74	21
75	21
76	21
77	21
78	21
79	8
80	8
81	8
82	8
83	8
84	7
85	8
86	8
87	7
88	21
89	8
90	20
91	8
92	7
93	8
94	8
95	7
96	8
97	8
98	8
99	8
100	8
101	8
102	7
103	8
104	8
105	8
106	8
107	8
108	8
109	8
110	8
111	8
112	8
113	8
114	8
115	8
116	8
117	8
118	7
119	30
120	8
121	8
122	8
123	8
124	8
125	21
126	20
127	8
128	8
129	21
130	21
131	9
132	8
133	20
134	20
135	8
136	7
137	8
138	8
139	8
140	8
141	8
142	8
143	8
144	8
145	8
146	8
147	8
148	8
149	8
150	8
151	8
152	8
153	8
154	8
155	8
156	8
157	10
158	10
159	10
160	10
161	10
162	10
163	10
164	10
165	10
166	10
167	10
168	10
169	10
170	10
171	10
172	10
173	10
174	10
175	10
176	10
177	10
178	10
179	10
180	10
181	10
182	10
183	10
184	10
185	10
186	10
187	10
188	10
189	8
190	8
191	8
192	8
193	10
194	10
195	10
196	10
197	10
198	10
199	10
200	10
201	10
202	10
203	10
204	10
205	10
206	10
207	10
208	10
209	10
210	10
211	10
212	10
213	10
214	10
215	10
216	10
217	10
218	10
219	10
220	10
221	10
222	10
223	10
224	10
225	8
226	8
227	22
228	8
229	20
230	9
231	9
232	14
233	14
234	14
235	14
236	14
237	14
238	14
239	14
240	14
241	14
242	14
243	14
244	14
245	14
246	14
247	14

Light in the Dark · Jan 4, 2024

You can't just Rain Man that list and the answer spits out like a rainbow after a rain storm?

R1ckyb0nd · Jan 5, 2024

Made some good progress today, I could not get the handshake to work, use pyserial so I just started sending the 44 request commands and it seems to return valid data.
Here is what was returned from a non-connected DCS using @kloppk's table.
As you can see there are some returns that are not 100% hex and I seem to not be getting the checksum each time. Look at battery voltage \x93\x02\xcc\x07Z' is returned taking 2 bytes for the data and reading it backwards give me 07cc which is 1996 which directly correlates to 19.96 volts that RMT shows. However I do not know what the Z is and it does not have the checksum.

??	\x93\x01\x02\x90'
Battery Current	\x93\x02 \x03\xb2'
BatteryVoltage	\x93\x02\xcc\x07Z'
??	\x93\x01\x00\x92'
??	\x93\x01\x00\x92'
Battleshort	\x93\x01\x01\x93'
CoolantTemp	\x93\x02\xff\x7f\x11'
FaultCode	\x93\x02\x00\x00\x91'
WarningNumber	\x93\x02\xb9\x01)'
??	\x93\x02\x00\x00\x91'
Battleshort	\x93\x01\x00\x92'
FuelLevel	\x93\x02\xfd\xff\x93'
BusFrequency?	\x93\x04\x00\x00\x00\x00\x97'
BusL1-L2	\x93\x02\x00\x00\x91'
BusL1-N	\x93\x02\x00\x00\x91'
BusL2-L3	\x93\x02\x00\x00\x91'
BusL2-N	\x93\x02\x00\x00\x91'
BusL3-L1	\x93\x02\x00\x00\x91'
BusL3-N	\x93\x02\x00\x00\x91'
??	\x93\x01\n\x98'
Contactor State 0=Open, 1=Closed	\x93\x01\x00\x92'
GensetFreq	\x93\x042\x00\x00\x00\xa5'
L1Current	\x93\x02\x00\x00\x91'
GensetL1-L2	\x93\x02\x00\x00\x91'
GensetL1-N	\x93\x02\x00\x00\x91'
L2Current	\x93\x02\x00\x00\x91'
GensetL2-L3	\x93\x02\x00\x00\x91'
GensetL2-N	\x93\x02\x00\x00\x91'
L3Current	\x93\x02\x00\x00\x91'
GensetL3-L1	\x93\x02\x00\x00\x91'
GensetL3-N	\x93\x02\x00\x00\x91'
EngineHours	\x93\x04\xfcA\x83\x00\xa9'
Battleshort	\x93\x01\x01\x93'
Power	\x93\x02\x00\x00\x91'
??	\x93\x01\x00\x92'
??	\x93\x01\x00\x92'
??	\x93\x01\x01\x93'
OilPressure	\x93\x02\xfd\x7f\x13'
Reconnect 2=120/240, 3=120, 0=208 ?? Need to recheck this	\x93\x01\x00\x92'
??	\x93\x02\x00\x00\x91'
??	\x93\x01\x00\x92'
??	\x93\x01\x00\x92'
??	\x93\x02\x00\x00\x91'
??	\x93\x01\x00\x92'

kloppk · Jan 5, 2024

Interesting. I tried to just send the 44 requests quite a while back and got no responses.
What baud rate are you using?

R1ckyb0nd · Jan 5, 2024

I went straight to 115200.
Can you post your C code for the math, I would like to see if I can mimic it in python?

kloppk · Jan 5, 2024

R1ckyb0nd said:
I went straight to 115200.
Can you post your C code for the math, I would like to see if I can mimic it in python?

Interesting. I'll have to try 115200 without handshaking the next time I fiddle with that project.
Which math? Decoding the values coming back from the DCS??

R1ckyb0nd · Jan 5, 2024

kloppk said:
Interesting. I'll have to try 115200 without handshaking the next time I fiddle with that project.
Which math? Decoding the values coming back from the DCS??

Yes like how do you pull the 2nd hex value to get the how many bytes the data is, then reverse digits, then convert to Dec.

kloppk · Jan 5, 2024

For example you read back \x93\x02\x00\x00\x91'
The 93 is just a transmission header. Ignore it.
The 02 indicates that the next 2 bytes are the data.
00 & 00 are the data.
The 91 is the checksum.

Here is the code I use to decode the data coming back from the DCS. The DCS response bytes are in decimal in the array DCSParams. It's a 44 x 7 array.
Each of the 44 DCS responses are stored in a single row in the array as they are read in. DCSParam[0,x] holds the first response, DCSParam[1,x] holds the second response, etc.
Since the number of bytes in each response is fixed I simply hard coded the decode for each DCS parameter.

Ignore the Serial Swap code. I use that for multiplexing the UART port on the 8266 between the DCS and the terminal display (Arduino)

///////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
///////////////////////////// Decode & Print Params Subroutine /////////////////////////////////////////////////////////
///////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////

void DecodeParams()
{

//Decode parameters

Serial.swap(); // Switch back to diagnostic port
delayMicroseconds(50);

// Row 0
float Pval = DCSParams[0][2]; //
Serial.print("Row 0 ?? ");
Serial.print(Pval);
Serial.println(" ");
delay(5); //Time for data to be printed on terminal

//Battery Current Row 1
Pval = DCSParams[1][3]; //
Pval = Pval * 256; //shift value to left 8 bits
Pval = Pval + DCSParams[1][2];
Serial.print("Row 1 BatteryCurrent ");
Serial.print(Pval);
Serial.println(" ");
delay(5); //Time for data to be printed on terminal

//Battery Voltage Row 2
Pval = DCSParams[2][3]; //
Pval = Pval * 256; //shift value to left 8 bits
Pval = Pval + DCSParams[2][2];
Pval = Pval / 100.0;
Serial.print("Row 2 BatteryVoltage ");
Serial.print(Pval);
Serial.println(" Volts");
delay(5); //Time for data to be printed on terminal

//Battle Short Status Row 3
Pval = DCSParams[3][2]; //
Serial.print("Row 3 BattleShort0=Off,1=ON ");
Serial.print(Pval);
Serial.println(" ");
delay(5); //Time for data to be printed on terminal

// Row 4
Pval = DCSParams[4][2]; //
Serial.print("Row 4 ?? ");
Serial.print(Pval);
Serial.println(" ");
delay(5); //Time for data to be printed on terminal

// Row 5
Pval = DCSParams[5][2]; //
Serial.print("Row 5 Battleshort? ");
Serial.print(Pval);
Serial.println(" ");
delay(5); //Time for data to be printed on terminal

//Coolant Temp Row 6
Pval = DCSParams[6][3]; //
Pval = Pval * 256; //shift value to left 8 bits
Pval = Pval + DCSParams[6][2];
Serial.print("Row 6 CoolantTemp ");
Serial.print(Pval);
Serial.println(" Degrees F");
delay(5); //Time for data to be printed on terminal

//Fault Code Row 7
Pval = DCSParams[7][3]; //
Pval = Pval * 256; //shift value to left 8 bits
Pval = Pval + DCSParams[7][2];
Serial.print("Row 7 FaultCode ");
Serial.print(Pval);
Serial.println(" ");
delay(5); //Time for data to be printed on terminal

//Warning Code Number Row 8
Pval = DCSParams[8][3]; //
Pval = Pval * 256; //shift value to left 8 bits
Pval = Pval + DCSParams[8][2];
Serial.print("Row 8 WarningCodeNumber ");
Serial.print(Pval);
Serial.println(" ");
delay(5); //Time for data to be printed on terminal

// Row 9
Pval = DCSParams[9][3]; //
Pval = Pval * 256; //shift value to left 8 bits
Pval = Pval + DCSParams[9][2];
Serial.print("Row 9 ?? ");
Serial.print(Pval);
Serial.println(" ");
delay(5); //Time for data to be printed on terminal

// Row 10
Pval = DCSParams[10][2]; //
Serial.print("Row 10 Battleshort ");
Serial.print(Pval);
Serial.println(" ");
delay(5); //Time for data to be printed on terminal

//Fuel Level Row 11
Pval = DCSParams[11][3]; //
Pval = Pval * 256; //shift value to left 8 bits
Pval = Pval + DCSParams[11][2];
Pval = Pval / 10.0;
Serial.print("Row 11 FuelLevel ");
Serial.print(Pval);
Serial.println(" %");
delay(5); //Time for data to be printed on terminal

//Bus Frequency Row 12
Pval = DCSParams[12][5];
Pval = Pval * 256; //shift value to left 8 bits
Pval = Pval + DCSParams[12][4];
Pval = Pval * 256; //shift value to left 8 bits
Pval = Pval + DCSParams[12][3];
Pval = Pval * 256; //shift value to left 8 bits
Pval = Pval + DCSParams[12][2];
Pval = Pval / 1000.0;
Serial.print("Row 12 BusFrequency ");
Serial.print(Pval);
Serial.println(" Hz");
delay(5); //Time for data to be printed on terminal

//Bus L1-L2 Row 13
Pval = DCSParams[13][3]; //
Pval = Pval * 256; //shift value to left 8 bits
Pval = Pval + DCSParams[13][2];
Serial.print("Row 13 BusL1-L2 ");
Serial.print(Pval);
Serial.println(" Volts");
delay(5); //Time for data to be printed on terminal

//Bus L1-N VAC Row 14
Pval = DCSParams[14][3]; //
Pval = Pval * 256; //shift value to left 8 bits
Pval = Pval + DCSParams[14][2];
Serial.print("Row 14 BusL1-N ");
Serial.print(Pval);
Serial.println(" Volts");
delay(5); //Time for data to be printed on terminal

//Bus L2-L3 Row 15
Pval = DCSParams[15][3]; //
Pval = Pval * 256; //shift value to left 8 bits
Pval = Pval + DCSParams[15][2];
Serial.print("Row 15 BusL2-L3 ");
Serial.print(Pval);
Serial.println(" Volts");
delay(5); //Time for data to be printed on terminal

//Bus L2-L3 Row 16
Pval = DCSParams[16][3]; //
Pval = Pval * 256; //shift value to left 8 bits
Pval = Pval + DCSParams[16][2];
Serial.print("Row 16 Voltage?? ");
Serial.print(Pval);
Serial.println(" Volts");
delay(5); //Time for data to be printed on terminal

//Bus L3-L1 Row 17
Pval = DCSParams[17][3]; //
Pval = Pval * 256; //shift value to left 8 bits
Pval = Pval + DCSParams[17][2];
Serial.print("Row 17 BusL3-L1 ");
Serial.print(Pval);
Serial.println(" Volts");
delay(5); //Time for data to be printed on terminal

//Bus L3-L1 Row 18
Pval = DCSParams[18][3]; //
Pval = Pval * 256; //shift value to left 8 bits
Pval = Pval + DCSParams[18][2];
Serial.print("Row 18 BusL3L1 ");
Serial.print(Pval);
Serial.println(" ");
delay(5); //Time for data to be printed on terminal

// Row 19
Pval = DCSParams[19][2]; //
Serial.print("Row 19 ?? ");
Serial.print(Pval);
Serial.println(" ");
delay(5); //Time for data to be printed on terminal

//ContactorState Row 20
Pval = DCSParams[20][2]; //
Serial.print("Row 20 ContactorState,0=Open,1=Closed ");
Serial.print(Pval);
Serial.println(" ");
delay(5); //Time for data to be printed on terminal

//Genset Freq Row 21
Pval = DCSParams[21][5];
Pval = Pval * 256; //shift value to left 8 bits
Pval = Pval + DCSParams[21][4];
Pval = Pval * 256; //shift value to left 8 bits
Pval = Pval + DCSParams[21][3];
Pval = Pval * 256; //shift value to left 8 bits
Pval = Pval + DCSParams[21][2];
Pval = Pval / 1000.0;
Serial.print("Row 21 GensetFreq ");
Serial.print(Pval);
Serial.println(" Hz");
delay(5); //Time for data to be printed on terminal

//L1 Current Row 22
Pval = DCSParams[22][3]; //
Pval = Pval * 256; //shift value to left 8 bits
Pval = Pval + DCSParams[22][2];
Pval = Pval / 10.0;
Serial.print("Row 22 L1Current ");
Serial.print(Pval);
Serial.println(" Amps");
delay(5); //Time for data to be printed on terminal

//Genset L1-L2 Row 23
Pval = DCSParams[23][3]; //
Pval = Pval * 256; //shift value to left 8 bits
Pval = Pval + DCSParams[23][2];
Serial.print("Row 23 GensetL1-L2 ");
Serial.print(Pval);
Serial.println(" Volts");
delay(5); //Time for data to be printed on terminal

//Genset L1-N Row 24
Pval = DCSParams[24][3]; //
Pval = Pval * 256; //shift value to left 8 bits
Pval = Pval + DCSParams[24][2];
Serial.print("Row 24 GensetL1-N ");
Serial.print(Pval);
Serial.println(" Volts");
delay(5); //Time for data to be printed on terminal

//L2 Current Row 25
Pval = DCSParams[25][3]; //
Pval = Pval * 256; //shift value to left 8 bits
Pval = Pval + DCSParams[25][2];
Pval = Pval / 10.0;
Serial.print("Row 25 L2Current ");
Serial.print(Pval);
Serial.println(" Amps");
delay(5); //Time for data to be printed on terminal

//Genset L2-L3 Row 26
Pval = DCSParams[26][3]; //
Pval = Pval * 256; //shift value to left 8 bits
Pval = Pval + DCSParams[26][2];
Serial.print("Row 26 GensetL2-L3 ");
Serial.print(Pval);
Serial.println(" Volts");
delay(5); //Time for data to be printed on terminal

//Genset L2-N Row 27
Pval = DCSParams[27][3]; //
Pval = Pval * 256; //shift value to left 8 bits
Pval = Pval + DCSParams[27][2];
Serial.print("Row 27 GensetL2-N ");
Serial.print(Pval);
Serial.println(" Volts");
delay(5); //Time for data to be printed on terminal

//L3 Current Row 28
Pval = DCSParams[28][3]; //
Pval = Pval * 256; //shift value to left 8 bits
Pval = Pval + DCSParams[28][2];
Pval = Pval / 10.0;
Serial.print("Row 28 L3Current ");
Serial.print(Pval);
Serial.println(" Amps");
delay(5); //Time for data to be printed on terminal

//Genset L3-L1 Row 29
Pval = DCSParams[29][3]; //
Pval = Pval * 256; //shift value to left 8 bits
Pval = Pval + DCSParams[29][2];
Serial.print("Row 29 GensetL3-L1 ");
Serial.print(Pval);
Serial.println(" Volts");
delay(5); //Time for data to be printed on terminal

//Genset L3-N Row 30
Pval = DCSParams[30][3]; //
Pval = Pval * 256; //shift value to left 8 bits
Pval = Pval + DCSParams[30][2];
Serial.print("Row 30 GensetL3-N ");
Serial.print(Pval);
Serial.println(" ");
delay(5); //Time for data to be printed on terminal

//Engine Hours Row 31
Pval = DCSParams[31][5]; //
Pval = Pval * 256; //shift value to left 8 bits
Pval = Pval + DCSParams[31][4];
Pval = Pval * 256; //shift value to left 8 bits
Pval = Pval + DCSParams[31][3];
Pval = Pval * 256; //shift value to left 8 bits
Pval = Pval + DCSParams[31][2];
Pval = Pval / 3600.0;
Serial.print("Row 31 EngineHours ");
Serial.print(Pval);
Serial.println(" ");
delay(5); //Time for data to be printed on terminal

// Row 32
Pval = DCSParams[32][2]; //
Serial.print("Row 32 Battleshort?? ");
Serial.print(Pval);
Serial.println(" ");
delay(5); //Time for data to be printed on terminal

//KiloWatts Row 33
Pval = DCSParams[33][3]; //
Pval = Pval * 256; //shift value to left 8 bits
Pval = Pval + DCSParams[33][2];
Pval = Pval / 10.0;
Serial.print("Row 33 Power ");
Serial.print(Pval);
Serial.println(" Kw");
delay(5); //Time for data to be printed on terminal

// Row 34
Pval = DCSParams[34][2]; //
Serial.print("Row 34 ?? ");
Serial.print(Pval);
Serial.println(" ");
delay(5); //Time for data to be printed on terminal

// Row 35
Pval = DCSParams[35][2]; //
Serial.print("Row 35 ?? ");
Serial.print(Pval);
Serial.println(" ");

// Row 36
Pval = DCSParams[36][2]; //
Serial.print("Row 36 ?? ");
Serial.print(Pval);
Serial.println(" ");
delay(5); //Time for data to be printed on terminal

//Oil Pressure Row 37
Pval = DCSParams[37][3]; //
Pval = Pval * 256; //shift value to left 8 bits
Pval = Pval + DCSParams[37][2];
Pval = Pval / 10.0;
Serial.print("Row 37 OilPressure ");
Serial.print(Pval);
Serial.println(" PSI");
delay(5); //Time for data to be printed on terminal

//Reconnect0=208, 2=120/240,3=120 Row 38
Pval = DCSParams[38][2]; //
Serial.print("Row 38 ?? ");
Serial.print(Pval);
Serial.println(" ");
delay(5); //Time for data to be printed on terminal

// Row 39
Pval = DCSParams[39][3]; //
Pval = Pval * 256; //shift value to left 8 bits
Pval = Pval + DCSParams[39][2];
Serial.print("Row 39 Reconnect0=208,2=120/240,3=120 ");
Serial.print(Pval);
Serial.println(" ");
delay(5); //Time for data to be printed on terminal

// Row 40
Pval = DCSParams[40][2]; //
Serial.print("Row 40 ?? ");
Serial.print(Pval);
Serial.println(" ");
delay(5); //Time for data to be printed on terminal

// Row 41
Pval = DCSParams[41][2]; //
Serial.print("Row 41 ?? ");
Serial.print(Pval);
Serial.println(" ");
delay(5); //Time for data to be printed on terminal

// Row 42
Pval = DCSParams[42][3]; //
Pval = Pval * 256; //shift value to left 8 bits
Pval = Pval + DCSParams[42][2];
Serial.print("Row 42 ?? ");
Serial.print(Pval);
Serial.println(" ");
delay(5); //Time for data to be printed on terminal

// Row 43
Pval = DCSParams[43][2]; //
Serial.print("Row 43 ?? ");
Serial.print(Pval);
Serial.println(" ");
delay(5); //Time for data to be printed on terminal

PassCount = PassCount + 1;

Serial.swap(); // Switch back to DCS
delayMicroseconds(50);
return;
}

///////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////
///////////////////////////////////////////////////////////////////////////////////////////////////////////////////////////

0	254
1	236
2	240
3	93
4	391
5	58
6	8
7	7
8	72
9	8
10	8
11	33
12	8
13	7
14	8
15	8
16	33
17	33
18	33
19	33
20	8
21	8
22	33
23	33
24	11
25	53
26	8
27	33
28	8
29	8
30	8
31	33
32	8
33	8
34	11
35	48
36	8
37	8
38	8
39	8
40	12
41	48
42	8
43	8
44	33
45	8
46	8
47	8
48	8
49	8
50	8
51	8
52	21
53	21
54	21
55	21
56	20
57	7
58	8
59	8
60	8
61	8
62	7
63	8
64	8
65	8
66	8
67	8
68	8
69	8
70	21
71	21
72	21
73	20
74	21
75	21
76	21
77	21
78	21
79	8
80	8
81	8
82	8
83	8
84	7
85	8
86	8
87	7
88	21
89	8
90	20
91	8
92	7
93	8
94	8
95	7
96	8
97	8
98	8
99	8
100	8
101	8
102	7
103	8
104	8
105	8
106	8
107	8
108	8
109	8
110	8
111	8
112	8
113	8
114	8
115	8
116	8
117	8
118	7
119	30
120	8
121	8
122	8
123	8
124	8
125	21
126	20
127	8
128	8
129	21
130	21
131	9
132	8
133	20
134	20
135	8
136	7
137	8
138	8
139	8
140	8
141	8
142	8
143	8
144	8
145	8
146	8
147	8
148	8
149	8
150	8
151	8
152	8
153	8
154	8
155	8
156	8
157	10
158	10
159	10
160	10
161	10
162	10
163	10
164	10
165	10
166	10
167	10
168	10
169	10
170	10
171	10
172	10
173	10
174	10
175	10
176	10
177	10
178	10
179	10
180	10
181	10
182	10
183	10
184	10
185	10
186	10
187	10
188	10
189	8
190	8
191	8
192	8
193	10
194	10
195	10
196	10
197	10
198	10
199	10
200	10
201	10
202	10
203	10
204	10
205	10
206	10
207	10
208	10
209	10
210	10
211	10
212	10
213	10
214	10
215	10
216	10
217	10
218	10
219	10
220	10
221	10
222	10
223	10
224	10
225	8
226	8
227	22
228	8
229	20
230	9
231	9
232	14
233	14
234	14
235	14
236	14
237	14
238	14
239	14
240	14
241	14
242	14
243	14
244	14
245	14
246	14
247	14

0	254
1	236
2	240
3	93
4	391
5	58
6	8
7	7
8	72
9	8
10	8
11	33
12	8
13	7
14	8
15	8
16	33
17	33
18	33
19	33
20	8
21	8
22	33
23	33
24	11
25	53
26	8
27	33
28	8
29	8
30	8
31	33
32	8
33	8
34	11
35	48
36	8
37	8
38	8
39	8
40	12
41	48
42	8
43	8
44	33
45	8
46	8
47	8
48	8
49	8
50	8
51	8
52	21
53	21
54	21
55	21
56	20
57	7
58	8
59	8
60	8
61	8
62	7
63	8
64	8
65	8
66	8
67	8
68	8
69	8
70	21
71	21
72	21
73	20
74	21
75	21
76	21
77	21
78	21
79	8
80	8
81	8
82	8
83	8
84	7
85	8
86	8
87	7
88	21
89	8
90	20
91	8
92	7
93	8
94	8
95	7
96	8
97	8
98	8
99	8
100	8
101	8
102	7
103	8
104	8
105	8
106	8
107	8
108	8
109	8
110	8
111	8
112	8
113	8
114	8
115	8
116	8
117	8
118	7
119	30
120	8
121	8
122	8
123	8
124	8
125	21
126	20
127	8
128	8
129	21
130	21
131	9
132	8
133	20
134	20
135	8
136	7
137	8
138	8
139	8
140	8
141	8
142	8
143	8
144	8
145	8
146	8
147	8
148	8
149	8
150	8
151	8
152	8
153	8
154	8
155	8
156	8
157	10
158	10
159	10
160	10
161	10
162	10
163	10
164	10
165	10
166	10
167	10
168	10
169	10
170	10
171	10
172	10
173	10
174	10
175	10
176	10
177	10
178	10
179	10
180	10
181	10
182	10
183	10
184	10
185	10
186	10
187	10
188	10
189	8
190	8
191	8
192	8
193	10
194	10
195	10
196	10
197	10
198	10
199	10
200	10
201	10
202	10
203	10
204	10
205	10
206	10
207	10
208	10
209	10
210	10
211	10
212	10
213	10
214	10
215	10
216	10
217	10
218	10
219	10
220	10
221	10
222	10
223	10
224	10
225	8
226	8
227	22
228	8
229	20
230	9
231	9
232	14
233	14
234	14
235	14
236	14
237	14
238	14
239	14
240	14
241	14
242	14
243	14
244	14
245	14
246	14
247	14

AMMPS Generator Series Remote Data

Well-known member

New member

Member

New member

Well-known member

Member

New member

Member

New member

Member

Member

New member

Well-known member

Well-known member

Member

Well-known member

Member

Well-known member

Member

Well-known member

0	254
1	236
2	240
3	93
4	391
5	58
6	8
7	7
8	72
9	8
10	8
11	33
12	8
13	7
14	8
15	8
16	33
17	33
18	33
19	33
20	8
21	8
22	33
23	33
24	11
25	53
26	8
27	33
28	8
29	8
30	8
31	33
32	8
33	8
34	11
35	48
36	8
37	8
38	8
39	8
40	12
41	48
42	8
43	8
44	33
45	8
46	8
47	8
48	8
49	8
50	8
51	8
52	21
53	21
54	21
55	21
56	20
57	7
58	8
59	8
60	8
61	8
62	7
63	8
64	8
65	8
66	8
67	8
68	8
69	8
70	21
71	21
72	21
73	20
74	21
75	21
76	21
77	21
78	21
79	8
80	8
81	8
82	8
83	8
84	7
85	8
86	8
87	7
88	21
89	8
90	20
91	8
92	7
93	8
94	8
95	7
96	8
97	8
98	8
99	8
100	8
101	8
102	7
103	8
104	8
105	8
106	8
107	8
108	8
109	8
110	8
111	8
112	8
113	8
114	8
115	8
116	8
117	8
118	7
119	30
120	8
121	8
122	8
123	8
124	8
125	21
126	20
127	8
128	8
129	21
130	21
131	9
132	8
133	20
134	20
135	8
136	7
137	8
138	8
139	8
140	8
141	8
142	8
143	8
144	8
145	8
146	8
147	8
148	8
149	8
150	8
151	8
152	8
153	8
154	8
155	8
156	8
157	10
158	10
159	10
160	10
161	10
162	10
163	10
164	10
165	10
166	10
167	10
168	10
169	10
170	10
171	10
172	10
173	10
174	10
175	10
176	10
177	10
178	10
179	10
180	10
181	10
182	10
183	10
184	10
185	10
186	10
187	10
188	10
189	8
190	8
191	8
192	8
193	10
194	10
195	10
196	10
197	10
198	10
199	10
200	10
201	10
202	10
203	10
204	10
205	10
206	10
207	10
208	10
209	10
210	10
211	10
212	10
213	10
214	10
215	10
216	10
217	10
218	10
219	10
220	10
221	10
222	10
223	10
224	10
225	8
226	8
227	22
228	8
229	20
230	9
231	9
232	14
233	14
234	14
235	14
236	14
237	14
238	14
239	14
240	14
241	14
242	14
243	14
244	14
245	14
246	14
247	14