Complete deuce winch mounting bolt list

[rolling18]

awesome info will be dooing this SOON!

YES!! ALMOST finished installing, completed the PTO install (slow)
now all I need is to install the pto driveshaft!!!

anyone know the what size the 4 bolts are that bolt it to the PTO flange???

then I get to figure out how to make the adjustments and fine tune the linkage..
TIPS???


and i need a PTO lever data plate.. what do they look like?

thanks!

 

[wsucougarx]

I've got a dataplate you can buy...but you'll have to buy the truck to get it. As far as the linkage is concerned. Lock out the PTO engagment handle into the hinged floor bracket, make sure your PTO is in neutral, then just adjust the linkage until you can freely put the pin in.

 

[rolling18]

I've got a dataplate you can buy...but you'll have to buy the truck to get it

Sure Ill buy the truck for the price of a data plate!! ill even double it!
im just not sure Witch plate i need for the in-cab control lever..:

 

[wsucougarx]

Here's what you need for the PTO engagement lever. This bracket locks out the handle in the NEUTRAL position. When you go to shift the PTO into gear, you simply rotate the lockout place via hinge
Saturn Surplus

Called the "winch control lock"

 

[rolling18]

Here's what you need for the PTO engagement lever. This bracket locks out the handle in the NEUTRAL position. When you go to shift the PTO into gear, you simply rotate the lockout place via hinge
Saturn Surplus

thank you I got that lock out part with the engagement handle part of the kit..
i was needing the data plate so I would know what each positions is, and espically if someone else drives/ needs to use the winch

 

[wsucougarx]

M35 Series Everything Else

No pic but item listing towards bottom of page, $8.50

 

[rolling18]

M35 Series Everything Else

No pic but item listing towards bottom of page, $8.50

found it!! thank you I will be ordering.

do I need the other "buzzer operation" for winch truck plate?

 

[wsucougarx]

You bet! If you do that, then you'll want to replace all your dataplates to match

 

[rolling18]

00ps! nevermind I already have the "Buzzer operation" with winch plate for some reason

 

[gringeltaube]

.......
anyone know the what size the 4 bolts are that bolt it to the PTO flange???.....

3/8"-24 x 1"

then I get to figure out how to make the adjustments and fine tune the linkage..
TIPS???
and i need a PTO lever data plate.. what do they look like?

Pics, below....

G.

 

[gringeltaube]

found it!! thank you I will be ordering......

Good luck if ordering from David Kelone (ex-MVDataplates).... 7 weeks since he got my $$ and no word, no action from his side, since then...!
Sorry, had to vent...

G.

 

[rolling18]

3/8"-24 x 1"


Pics, below....

G.

perfect thank you !
until I get the plane I will have to write it heh..

 

[rolling18]

Here's what you need for the PTO engagement lever. This bracket locks out the handle in the NEUTRAL position. When you go to shift the PTO into gear, you simply rotate the lockout place via hinge
Saturn Surplus

Called the "winch control lock"

I made a similar device out of a door hinge to "lock" the hi - low lever into hi position works great!

 

[JCKnife]

Bumping a very useful thread, and adding a pic: this is what $80 worth of 11" bolts looks like. Really after installing I think 10" would have worked, but no harm.

 

[gringeltaube]

................Really after installing I think 10" would have worked, but no harm.

Well, the original bolts actually are 10-1/4" for the 1/2", and 10-1/2" for the 5/8", respectively. But not always that easy to find...

For better looks you can always shorten them, or install a second lifting bracket, underneath the bumper...

G.

 

[treeguy]

Real quick, I think I might have said 11" if you were going to install the shackle mounts like Gringeltaube is showing above. Also, if you do, you will need to trim the exposed threads near flush with the nuts to get a bow shackle to fit without jamming into them.

I'm glad this is helping some people! Keep up the good work!

 

[clinto]

When you got the frame extentions, did you also get the three 1/2"diameter tubes

Much thanks for this awesome post, I am about to spend about $100 on bolts to finish my install up.

Where did you find the 1/2" tubes on their site?

I don't see hollow tubes in the steel section: https://www1.mscdirect.com/eCommerc..._/N-77dtr?cm_re=Category-_-Breadcrumb-_-Steel

Much thanks

C

 

[JCKnife]

In hindsight the 11" bolts from MSC are rusting quickly. They are the only bolts on my bumper assembly rusting. I think I am going to go back and see if McMaster-Carr has 10" bolts with zinc coating or more protection. Hate to waste $80 but lesson learned.

 

[clinto]

In hindsight the 11" bolts from MSC are rusting quickly.

Did you paint them? I am going to clean/epoxy prime/paint mine, hopefully I won't have this issue.

 

[JCKnife]

No I primered the bumper and extensions but have not painted yet. The black bolts from MSC are the only ones rusty after maybe a month and a half?

I'm going to order these instead:

LineQuantityProduct
ShipsUnit priceTotalDelete1packs
91257A501
Grade 8 Alloy Steel Hex Head Cap Screw Zinc Yellow-Plated, 1/2"-20 Thread, 10" Length




today$9.68 pack38.72
2packs
91257A838
Grade 8 Alloy Steel Hex Head Cap Screw Zinc Yellow-Plated, 5/8"-18 Thread, 10" Length




today10.38 pack20.76