• Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!

  • Microsoft MSN, Live, Hotmail, Outlook email users may not be receiving emails. We are working to resolve this issue. Please add support@steelsoldiers.com to your trusted contacts.

Isuzu powered Drash 5 pin connectors

98G

Former SSG
Steel Soldiers Supporter
6,063
4,408
113
Location
AZ/KS/MO/OK/NM/NE, varies by the day...
They aren't specific to the Isuzu version. What they are is a 60amp 3phase plug, used in several different applications.

They are hideously expensive. I have the part numbers somewhere (New phone, lost a bunch of stuff), and I'll post them if I can find them again.
 

Coug

Well-known member
Steel Soldiers Supporter
2,954
4,300
113
Location
Olympia/WA
This link is to the datasheet showing the military cable connector identification system


And these links match what those numbers say, and also match the "UEC 32-12" spacer in the middle of the one you posted a picture of in the other forum


roughly $350ish for the cable ends, and $160ish for the equipment mount ends.
Pretty spendy, but not the worst I've ever seen.

For that kind of pricing considering we were discussing you using it as a load bank for your MEP803, you might be better off just buying some 240V shop heaters as have been discussed on other threads. They will give you better control over the amount of load, and you don't have to open up the ECU and disable any of the heat coils to bring the load down.
 
Last edited:

robertsears1

Active member
255
119
43
Location
Near Apex/NC
Look closely on the green rubber area and you may see a number, should be 32-12 as mentioned above. That kind of connector is on the FDECU (field deployable environmental control unit). Look on ebay under 32-12 connector. The female end seems harder to find. I got a couple for around $75 and felt lucky.

Robert
 
Last edited:

Zed254

Well-known member
866
466
63
Location
S. Hampton Roads, VA
I like the price of these connectors for my MEP-803A. However, these are 3 phase .... meaning the spades turn in toward center of connector versus the similar single phase 50 amp connectors (think CEP spider box) with spades that turn outward. The ones I received looked like they had been plugged in one time = excellent condition.

 

Guyfang

Moderator
Staff member
Moderator
16,644
23,769
113
Location
Burgkunstadt, Germany
Why do you have two threads for this problem? Please have one deleted. It makes old people like me crazy, trying to keep up with you.
 

Light in the Dark

Well-known member
Steel Soldiers Supporter
3,799
5,819
113
Location
MA

98G

Former SSG
Steel Soldiers Supporter
6,063
4,408
113
Location
AZ/KS/MO/OK/NM/NE, varies by the day...
Maybe you should ask @Suprman if these cables will work here... or at least to get better markings off them for you. Price is certanly right if so!

This us the parallel cable. Different pins, much smaller. Will not work for the 60amp J1 port.
 

Mk23

Active member
Steel Soldiers Supporter
124
81
28
Location
Port Angeles, WA
Thank you for pointing that out!! Actually seller does have a cable I could use, but it $400. A bit more than I would like to spend...

 
Last edited:

Coug

Well-known member
Steel Soldiers Supporter
2,954
4,300
113
Location
Olympia/WA
Thank you for pointing that out!! Actually seller does have a cable I could use, but it $400. A bit more than I would like to spend...

plus shipping brings it over $500. A lot more than I would want to spend without it being a necessity.
 

98G

Former SSG
Steel Soldiers Supporter
6,063
4,408
113
Location
AZ/KS/MO/OK/NM/NE, varies by the day...
Thank you for pointing that out!! Actually seller does have a cable I could use, but it $400. A bit more than I would like to spend...

That's the correct cable, and not a bad price really. You can't buy the components for that.

If I didn't already have one, I'd be buying it.
 
Top