• Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!

  • Microsoft MSN, Live, Hotmail, Outlook email users may not be receiving emails. We are working to resolve this issue. Please add support@steelsoldiers.com to your trusted contacts.

M1079 leaking air out the front bumper "Service" glad hand vent

321
14
18
Location
Montana
Been working on my truck allot and never noticed the front blue service glad hand leaking air only when I push the brakes, I don't recall this happening before, Is this normal?

Seth
 

Smike740

Member
Steel Soldiers Supporter
199
15
18
Location
Columbus, Ohio
No, this has been discussed in prior threads, I believe there is a check valve behind the bumper that is the cause. My truck was leaking at the red glad hand, in that case the shuttle valve under the step needed replaced.
 

NDT

Well-known member
Steel Soldiers Supporter
10,498
6,631
113
Location
Camp Wood/LC, TX
I searched "gladhand" in the FMTV forum and could only find discussions of the EMERGENCY side leaking. Sounds like one of the checkvalves.
 

Smike740

Member
Steel Soldiers Supporter
199
15
18
Location
Columbus, Ohio
I just checked the Air line diagram in the TM, it looks like the two way check valves under the drivers step is likely where the problem lies. The one behind the bumper is for the emergency gladhand. Here is a picture from the manual hope this helps.
 

Attachments

321
14
18
Location
Montana
awesome, I will locate the parts and give it a whirl, you guys rock!!!!!!

Seth

I just checked the Air line diagram in the TM, it looks like the two way check valves under the drivers step is likely where the problem lies. The one behind the bumper is for the emergency gladhand. Here is a picture from the manual hope this helps.
 

wheelspinner

Well-known member
Steel Soldiers Supporter
3,752
1,529
113
Location
North Carolina - FINALLY !
I just replaced all threee of those check valves. They have old dried up rubber diaphragms in them, They are not expensive and pretty easy to change. Just do all three at once and be done.

PS, take a few good pics of the layouts of the fittings, you will need that to keep track of all the lines as they are all the same color
 

FloridaAKM

Well-known member
2,699
392
83
Location
Gainesville, Florida
You can get kits to replace the diaphragms or new units & save the old units for rebuild. They also offer actual shuttle valve replacement units vs the ones with rubber diaphragms. Been there, done that, but no Tshirts were available. I had a similar problem with my truck & the repairs fixed the air leaking issues.
 

spankybear

Well-known member
898
924
93
Location
WA

coachgeo

Well-known member
5,150
3,466
113
Location
North of Cincy OH
Have you downloaded the 24P part TM? That's a good start for part numbers. ...
1. If it twas a snake it would have bit you..... the very first forum on the very front page of this Steel Soldiers Bulletin Board contains links to the TM's (Tech. Manuals).
2. the very top of this FMTV forum contains another one that if it twas a snake; would have bit ya.... there is a sticky at the top about a spreadsheet full of part numbers commonly asked about....

two snake bites.... owww... that has got to hurt lol. Oh well..... we all live and learn right.
 
Last edited:

Coffey1

Well-known member
Steel Soldiers Supporter
3,871
497
83
Location
Gray Court SC
Seth it's the check valve right behind the passenger side shackle
You will have to remove those covers under bumper to get to it.
You can see it by looking thru the top of bumber and bottom of grill.
 

Mike Robo

New member
5
0
1
Location
Boston Mass
I have a similar issue with the front Blue glad hands front and back leaking air when i press the brake pedal. I removed them and plugged them up with a brass fitting. Now when i apply the brakes, the whole truck locks up. The reason i'm trouble shooting the brakes is thier was very little braking power to the rear wheels. I adjusted the rear brakes they are operating as they should. Im new to the site so and to online forums, so if Im hijacking your thread please let me know. Thanks Mike
 

Plasa

Well-known member
Steel Soldiers Supporter
256
322
63
Location
Italy
You can get kits to replace the diaphragms or new units & save the old units for rebuild. They also offer actual shuttle valve replacement units vs the ones with rubber diaphragms. Been there, done that, but no Tshirts were available. I had a similar problem with my truck & the repairs fixed the air leaking issues.
Hello!
Do you have a part number for the repair kit?

Thanks!

Christian
 

Plasa

Well-known member
Steel Soldiers Supporter
256
322
63
Location
Italy
which valve and I'll see if can find repair kit number....... and get it put into the spreadsheet. I help maintain the sheet along with Wes.
This one: N30252B on TM ...-24P, page 383, item no. 18.

Thanks a lot!

Christian
 
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website like our supporting vendors. Their ads help keep Steel Soldiers going. Please consider disabling your ad blockers for the site. Thanks!

I've Disabled AdBlock
No Thanks