• Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!

  • Microsoft MSN, Live, Hotmail, Outlook email users may not be receiving emails. We are working to resolve this issue. Please add support@steelsoldiers.com to your trusted contacts.

 

My M813 gets a turbo!

US6x4

Well-known member
Steel Soldiers Supporter
1,165
2,027
113
Location
Wenatchee, WA
I made some more progress on the intake piping between the air cleaner and the turbo and I got the stack & heat shield installed.
Looks like I didn't need to buy an extension splice as the 4" length I cut off the stock intake pipe is the right size to space the 90° elbow off the air cleaner for a straight shot to the turbo. Pretty neat how that worked out.

I cut the 4" off, rolled beads on the smooth ends, had some 3/16" flat bar rolled to 5" ID and cut out a tab to TIG weld on and then tap 1/8" NPT for the air restriction gauge tube.

20210823_090324.jpg
20210823_091021.jpg
20210824_130525.jpg
20210825_090056.jpg
20210825_090125.jpg
20210826_113025.jpg
20210826_130322.jpg
20210828_100206.jpg
20210828_095904.jpg
20210828_095849.jpg
 

Mullaney

Well-known member
Steel Soldiers Supporter
Supporting Vendor
7,251
18,786
113
Location
Charlotte NC
I made some more progress on the intake piping between the air cleaner and the turbo and I got the stack & heat shield installed.
Looks like I didn't need to buy an extension splice as the 4" length I cut off the stock intake pipe is the right size to space the 90° elbow off the air cleaner for a straight shot to the turbo. Pretty neat how that worked out.

I cut the 4" off, rolled beads on the smooth ends, had some 3/16" flat bar rolled to 5" ID and cut out a tab to TIG weld on and then tap 1/8" NPT for the air restriction gauge tube.

View attachment 843744
View attachment 843745
View attachment 843746
View attachment 843747
View attachment 843748
View attachment 843749
View attachment 843750
View attachment 843751
View attachment 843752
View attachment 843753
.
Getting better by the day!
Nice metal skills for sure.
 

Valor

Active member
185
192
43
Location
Apple Valley, Ca.
I made some more progress on the intake piping between the air cleaner and the turbo and I got the stack & heat shield installed.
Looks like I didn't need to buy an extension splice as the 4" length I cut off the stock intake pipe is the right size to space the 90° elbow off the air cleaner for a straight shot to the turbo. Pretty neat how that worked out.

I cut the 4" off, rolled beads on the smooth ends, had some 3/16" flat bar rolled to 5" ID and cut out a tab to TIG weld on and then tap 1/8" NPT for the air restriction gauge tube.

View attachment 843744
View attachment 843745
View attachment 843746
View attachment 843747
View attachment 843748
View attachment 843749
View attachment 843750
View attachment 843751
View attachment 843752
View attachment 843753
You are very fortunate to have access to all that fabrication equipment and have that knowledge. Great job. Thanks for sharing all of your work with this.
 

US6x4

Well-known member
Steel Soldiers Supporter
1,165
2,027
113
Location
Wenatchee, WA
You are very fortunate to have access to all that fabrication equipment and have that knowledge. Great job. Thanks for sharing all of your work with this.
Yes, I'm very fortunate to have a full manufacturing shop at my disposal and fortunate to be working with dozens of skilled fabricators & machinists. I sure don't take it for granted because for maybe 15 years I had to make due with improvisations like using a hammer & punch instead of a press, or a vise & crescent wrench instead of a press-brake, or a hacksaw instead of a band saw.

I do keep mental notes on what I use the most so that I could equip my own shop/garage if these perks ever go away.

I'm happy to share. Showing all the steps might share some ideas and it for sure will show people how much is involved with these projects.
 
Last edited:

hethead

Active member
147
216
43
Location
Seattle, WA.
Thank you! I didn't quite get around to driving it this weekend like i had planned but I should be done with the entire install tomorrow. I want to do some shake down runs before I do any filming so it may be a week or two yet.
Just jot down your egt's, boost, fuel pressures (if you got em) etc. I'm curious to see what you have and can selfishly learn from it!
 

US6x4

Well-known member
Steel Soldiers Supporter
1,165
2,027
113
Location
Wenatchee, WA
To cut the hole in the passenger side panel for the air intake i first trimmed back the stiffener rib and I had a 6 3/8" i.d. stencil made from 10 ga. that will produce a 6" hole with the plasma cutter. The fit was so close to the panel latches and hinge that the stencil had to trimmed but the hole itself will barely clear.

20210828_183924.jpg

20210828_190409.jpg
A sturdy putty knife and a hammer sliced through the spot welds easily enough.

20210830_111800.jpg
I edged the hole with my favorite rubber trim which had to be clearanced in places to miss the latch & hinge.
20210831_152641.jpg

20210831_152546.jpg

The short section of hose that joined the 4" extension pipe to the air cleaner was actually a donor part from my original air cleaner elbow.
20210424_144534.jpg

20210831_160110.jpg

20210831_160120.jpg

20210831_160130.jpg

The 90° elbow leading into the turbo compressor is 5 1/2" I.D. on the turbo side and 5" I.D. on the intake tube side.
 
Last edited:

Mullaney

Well-known member
Steel Soldiers Supporter
Supporting Vendor
7,251
18,786
113
Location
Charlotte NC
To cut the hole in the passenger side panel for the air intake i first trimmed back the stiffener rib and I had a 6 3/8" i.d. stencil made from 10 ga. that will produce a 6" hole with the plasma cutter. The fit was so close to the panel latches and hinge that the stencil had to trimmed but the hole itself will barely clear.

View attachment 843937

View attachment 843938
A sturdy putty knife and a hammer sliced through the spot welds easily enough.

View attachment 843939
I edged the hole with my favorite rubber trim which had to be clearanced in places to miss the latch & hinge.
View attachment 843940

View attachment 843941

The short section of hose that joined the 4" extension pipe to the air cleaner was actually a donor part from my original air cleaner elbow.
View attachment 843944

View attachment 843942

View attachment 843943

View attachment 843946
'
I know we keep saying it - but wow that is amazing.
It all looks as good as if it was done in a truck factory.

Sharp for sure!
 

US6x4

Well-known member
Steel Soldiers Supporter
1,165
2,027
113
Location
Wenatchee, WA
And...that's a wrap! This turbo install is finished! Phew!...that only took 4 months...plus the 4 months of researching and buying parts before that. By far my most intense project to date but I think it turned out pretty nice. After some test drives I will be swapping out the fuel button for a #17.

20210831_160137.jpg

20210831_160251.jpg

20210831_160219.jpg

20210831_160235.jpg

20210831_160318.jpg
 

SCM35A2

Well-known member
Steel Soldiers Supporter
1,974
2,645
113
Location
Florence, SC

Crf450x

Well-known member
275
347
63
Location
Fall Branch, TN
This is the best thread I’ve ever seen on here. You did an absolutely incredible job. Also a great job with pictures and documenting.

Keep us updated on how the paint holds up. I’ve tried a couple different paints over the years on manifolds and never could get them to last very long (admittedly that truck regularly saw 2000° egt). I didn’t even paint the one on my 5 ton.

It will be like a new truck when you swap the fuel button.

Also, we definitely need a driving video!
 

US6x4

Well-known member
Steel Soldiers Supporter
1,165
2,027
113
Location
Wenatchee, WA
This is the best thread I’ve ever seen on here. You did an absolutely incredible job. Also a great job with pictures and documenting.

Keep us updated on how the paint holds up. I’ve tried a couple different paints over the years on manifolds and never could get them to last very long (admittedly that truck regularly saw 2000° egt). I didn’t even paint the one on my 5 ton.

It will be like a new truck when you swap the fuel button.

Also, we definitely need a driving video!

Well thanks man, glad you like it! I really hope the paint holds out and it's a bit of an experiment to see how it does with the heat, grease/oil, and the UV exposure on the stack. I'll keep the group updated as it ages so we know if it's worth the cost or not $$$.

I'm thinking I'll have to commandeer my daughter's faux-pro for some driving vids...
 

hethead

Active member
147
216
43
Location
Seattle, WA.
I think you'll really like the 17 button. I put a 15 in mine and I have to keep a pretty light touch on the pedal to keep the fuel pressure down a bit, where I like it. I'll probably end up putting a 17 (or close to it) in. I don't know if you have a fuel press. gauge or not, but I'm glad I put one in.
 

US6x4

Well-known member
Steel Soldiers Supporter
1,165
2,027
113
Location
Wenatchee, WA
Well, the first test drive was a success! No leaks, no cracks, no misses, no smoke, no fires, no cops, no tow trucks, no heat issues, and also... no video...sorry.

What i did have was lots of throaty exhaust roar, turbo whine, and jake brake bark 😁

The new 5" exhaust with short muffler is substantially louder but it sounds GOOD! - especially when you push in the clutch to shift and it changes from a 2000 rpm roar to the whistling turbo unwinding.

On a gradual hill doing 40 in 4th I saw about 9 psi and egt's around 800°F pre-turbo with the stock fuel button and dual fuel mod.

After another cruise or two I'll swap in the #17.
 

Mullaney

Well-known member
Steel Soldiers Supporter
Supporting Vendor
7,251
18,786
113
Location
Charlotte NC
Well, the first test drive was a success! No leaks, no cracks, no misses, no smoke, no fires, no cops, no tow trucks, no heat issues, and also... no video...sorry.

What i did have was lots of throaty exhaust roar, turbo whine, and jake brake bark 😁

The new 5" exhaust with short muffler is substantially louder but it sounds GOOD! - especially when you push in the clutch to shift and it changes from a 2000 rpm roar to the whistling turbo unwinding.

On a gradual hill doing 40 in 4th I saw about 9 psi and egt's around 800°F pre-turbo with the stock fuel button and dual fuel mod.

After another cruise or two I'll swap in the #17.
.
That is fantastic!
Glad to hear about it - and when you get the chance - you need a co-pilot to grab some video and snap pictures :)
 

US6x4

Well-known member
Steel Soldiers Supporter
1,165
2,027
113
Location
Wenatchee, WA
Today I swapped out the fuel button for a #17 and was surprised to find a #37 in the pump. I was expecting a #28 based on what most people report finding in their rigs. I wonder if M816s have lower number buttons than M813s because of their weight?...

The button in the pump read "37 USA MS"
(No Cummins part number on it)

20210911_162109.jpg

20210911_160018.jpg
17 on left, 37 on right.
 

US6x4

Well-known member
Steel Soldiers Supporter
1,165
2,027
113
Location
Wenatchee, WA
I took the same route for a second test drive now with the #17 button and it feels like I went from a loaded truck to an empty truck 😁

On the same incline where it was 9 psi/800° it was now 11+ psi/800°.

I'm not really running around to do data logging I'm just noting what I saw at a glance - mainly concerned with the egt's. So far so good!
 
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website like our supporting vendors. Their ads help keep Steel Soldiers going. Please consider disabling your ad blockers for the site. Thanks!

I've Disabled AdBlock
No Thanks