- 805
- 71
- 28
- Location
- Kennewick, WA
Wow that a whole lot of $#!+. Maybe pull the oil fill cap and insert the hose from the shop vac into the exhaust. And have a couple of new bags at the ready.
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
Operation "URGENT RESTORATION"
- Thread starter m38inmaine
- Start date
wsucougarx
Well-known member
- 6,951
- 67
- 48
- Location
- Washington State
Oh my goodness...yikes!!!
- 2,118
- 67
- 48
- Location
- Maine USA
I sucked out a lot more from the manifold last night, there was even what appeared to be roots growing in there, before you know I think a tree would have sprouted. I have the manifold nuts soaking in Kroil and Ill take them off tonight and see what evil lurks behind it.
- 2,118
- 67
- 48
- Location
- Maine USA
Pulled the manifold tonight, just as I suspected all packed in with acorn crap and it looks like all the exhaust valve stems are rusted. And I'm sure which ever valves may have been open crap leaked into the cylinders. Head is off next.
Attachments
- 5,637
- 381
- 83
- Location
- Spring Branch, TX
Nasty. Still your engine and engine compartment look cleaner than mine.
- 2,118
- 67
- 48
- Location
- Maine USA
It really sucks as the engine is very clean and shows no sign of oil leaks, hopefully the head can be repaired.
- 2,118
- 67
- 48
- Location
- Maine USA
Here are the pictures that tell the story of the stuck engine. All because a critter crawled up into the exhaust and made a root cellar. You can see where the debris leaked down into the cylinders, #3 was the worst with a big hunk of nasty, looks like a domed piston. So now the engine had to come out, re sleeve etc. The Gama Goat, the gift that just keep on giving. OH yeah, and that head is one heavy mother by yourself!
Attachments
Last edited:
combat32
Well-known member
- 1,639
- 106
- 63
- Location
- Booneville AR.
Well that kinda sucks, but I think red river has the whole rebuild kit I just got a gasket set, not sure on his price on that.
combat32
Well-known member
- 1,639
- 106
- 63
- Location
- Booneville AR.
Well here ya go Mark, got everything but the bulkead behind the driver position, for the life of me can't figure out how to get it out, probably the gas wrench is the only way and I didn't have one today. The console only has the panel on the dvr side, I had to do some upsidedown cuttin to get her out, hopefully it will work for you. The other parts are bent a bit but should straighten out, except the headlight rings which look perfect
Attachments
- 5,637
- 381
- 83
- Location
- Spring Branch, TX
If you run across another one of the blackout light guards I need one. I've got one off of a 151 (3 bolt) at the moment that is good from a distance but is obviously incorrect once you get close.
combat32
Well-known member
- 1,639
- 106
- 63
- Location
- Booneville AR.
I will keep an eye out for one Mark
- 2,118
- 67
- 48
- Location
- Maine USA
Wow Tom, that looks great, I needed some good news. That center air duct was weighing on my mind as it's not a separate part. Hopefully by now the blood has drained back where it belongs. Again, many thanks and a great job.
- 2,118
- 67
- 48
- Location
- Maine USA
Found these in the yard when I arrived home from work today, another piece to the puzzle. I think some one here needed a horn bracket, have an extra now. Also worked on some parts Tom sent me and need to get those pictures posted as well. Nice to see a lot of activity on the Goat forum.
Attachments
combat32
Well-known member
- 1,639
- 106
- 63
- Location
- Booneville AR.
What's that other bracket on pass side fender?
M8 alarm or something else.
M8 alarm or something else.
- 2,118
- 67
- 48
- Location
- Maine USA
It's for a DS2 bottle, never seen one like it before, jerks mounted it crooked as ****.
combat32
Well-known member
- 1,639
- 106
- 63
- Location
- Booneville AR.
Must be old school M 11 bracket, I think I remember those,
- 2,118
- 67
- 48
- Location
- Maine USA
Pulled the engine today, not too bad but I did catch a couple of lines that still needed to be un hooked just in time. I don't have enough room in my garage to have the engine on the floor so I have it in the back of the carrier and pushed it in nose first. Will make working on the engine a little tougher but I had no extra space. No fancy steel stands, a pallet, railroad ties and 4x4's but it works and is solid.
Attachments
- 5,637
- 381
- 83
- Location
- Spring Branch, TX
I'm done with mine if you want to borrow them.
combat32
Well-known member
- 1,639
- 106
- 63
- Location
- Booneville AR.
Lookin good Mark!
- 2,118
- 67
- 48
- Location
- Maine USA
Yesterday I drained the engine oil and removed all the pan bolts which came out easy, let it drain over night. Today I found the pan had taken itself off and was lying on the pallet, ok one less thing to do.
After a lot of looking over I dove into removing the twin oil pick ups, a lot going on here. After a half hour or so had all that off, removed the rod cap nuts off number 3 the worst looking hole. Plan A was to weld a plate with a captive nut and use the slide hammer to pull the sleeve, well I guess the sleeve is probably cast iron or such and my mig won't weld to it. So plan B I may try and use a air chisel/hammer with an extended rod to push it out from the bottom. Perhaps some one will chime in with a better idea.
After a lot of looking over I dove into removing the twin oil pick ups, a lot going on here. After a half hour or so had all that off, removed the rod cap nuts off number 3 the worst looking hole. Plan A was to weld a plate with a captive nut and use the slide hammer to pull the sleeve, well I guess the sleeve is probably cast iron or such and my mig won't weld to it. So plan B I may try and use a air chisel/hammer with an extended rod to push it out from the bottom. Perhaps some one will chime in with a better idea.
Attachments
Last edited: