Firehound
Active member
- 178
- 103
- 43
- Location
- New Caney, TX
Chevy K20 (basically a CUCV pickup) and M101. Stranded in Grand Junction, Colorado. Trying to get home to Houston, TX. Will pay $$$!!!
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
Stranded in Grand Junction, Colorado.
- Thread starter Firehound
- Start date
- 6,426
- 4,985
- 113
- Location
- Ft. Lauderdale, Florida
Grand Junction is a nice place to be stranded, Mo better than the jungle.
I know, I know, that comment did Not help at all.
Last time I was stranded in GJ I rented an plane and went and looked around.
Place was built by the railroads.
I know, I know, that comment did Not help at all.
Last time I was stranded in GJ I rented an plane and went and looked around.
Place was built by the railroads.
- 10,458
- 6,530
- 113
- Location
- Camp Wood/LC, TX
That’s a thousand miles away, best hot shot haul rate you will get is $2.00/mile, suggest fix whatever failed right there with that money rather than blow it on hauling.
unitedstatesoffreight
Active member
- 199
- 121
- 43
- Location
- Delray Beach, FL
Hey @Firehound my name is Nick with United States of Freight. I’d be happy to help, feel free to call me at 484-431-9509.
Firehound
Active member
- 178
- 103
- 43
- Location
- New Caney, TX
I've been at it for 3 days... changed almost everything. I'll pay the hotshot rate, if someone knows a reputable hot shotter!
- 10,458
- 6,530
- 113
- Location
- Camp Wood/LC, TX
Nick at USF above will take perfect care of you
- 10,458
- 6,530
- 113
- Location
- Camp Wood/LC, TX
Dude next time put out a sos on here, most of us are squarebody Chevy sme’s so chances are we could have walked you through your issues.
Firehound
Active member
- 178
- 103
- 43
- Location
- New Caney, TX
I will! I didnt, because it's not a CUCV, and I didn't want to get in trouble.
But, I'm at a loss. It bogs down and dies at speed. Idle? Purrs like a kitten. Not a fuel issue, not a spark issue. 3 days in, and I, and my mechanic buddy's are out of ideas... I've replumbed the fuel to come out of the transfer tank in the bed through an electrical pump. Swapped carbs (carb #3 going on right now) replaced the ignition coil and ignition control module....
(1986 K20 pickup. 4speed manual, 400 small block.)
- 10,458
- 6,530
- 113
- Location
- Camp Wood/LC, TX
Have you replaced the plug wires.
M35fan
Well-known member
- 1,166
- 3,992
- 113
- Location
- Arab, Alabama
Not to confuse the issue at hand, but do you have a way to check your timing? I had a similar problem on an 84 Oldsmobile on my way back home from TX once, and the cause was my timing gear missing several teeth. Good luck to you, hope you make it home safely.
Firehound
Active member
- 178
- 103
- 43
- Location
- New Caney, TX
I've checked the wires... I have not checked the timing for a broken tooth, but things did improve when we retarded the timing a bit
- 10,458
- 6,530
- 113
- Location
- Camp Wood/LC, TX
How did you check the wires? When resistor wires degrade they don't pass enough energy to fire the plug when the engine is under load.
Firehound
Active member
- 178
- 103
- 43
- Location
- New Caney, TX
I ran a continuity test. And they are new wires (About a year old. Have sat most of that year.)
- 2,661
- 2,195
- 113
- Location
- Sunman Indiana
I would do a compression check, possibly cooked some pistons at altitude. Also, feed directly from a fuel can strapped to the roof to the carb, to eliminate tank/pump problems. Check timing chain and gears. Lastly throw a new complete distributor in it before paying 2k to have it towed. Or a fully dressed junkyard motor, as far as that goes...
- 2,661
- 2,195
- 113
- Location
- Sunman Indiana
Did you ever figure out what was causing your problem?
Firehound
Active member
- 178
- 103
- 43
- Location
- New Caney, TX
Not yet... I bought a new vacuum advance tonight, I'm gonna toss it on and see what happens...
K10A
Member
- 225
- 5
- 18
- Location
- Western Co
I may be heading down that way this week , pm me if you still need help.
Firehound
Active member
- 178
- 103
- 43
- Location
- New Caney, TX
The truck is down here in Texas now, but if you're good with setting timing, come on down!! At this point, I think that it has to have skipped a tooth on the timing chain... I'm really tempted to throw a 6.2 in it at this point!!
- 2,661
- 2,195
- 113
- Location
- Sunman Indiana
You can usually rock the motor back and forth and get an idea how sloppy the timing chain is by watching the rotor button. Also, trying to time a distributor if the vale timing is out is going to be a futile effort.