71DeuceAK
Well-known member
- 1,513
- 416
- 83
- Location
- Fairbanks, Alaska
Probably not! That said, once I get mine I plan on doing that in a controlled environment. 
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
What have you done to your 5 ton this week?
- Thread starter dezert ratt
- Start date
twisted60
Well-known member
- 617
- 250
- 63
- Location
- Jupiter, Florida
Crawled back under my truck today and checked the air lines for the front wheel drive lock in, they were connected wrong, just as in the other thread about how to check and see if front wheels were engaged or not. Before I swapped the lines in question I followed the checks and my truck failed, so I swapped the lines and she did just as she is supposed to, buildup full air pressure, jack up 1 front wheel and give it a spin, if lines are correct with transfer case in high range and front wheel switch on dash in "out" wheel and drive shaft will spin. While I was under there I pulled off the big washer that locks in front wheels when shifting into low range, now I can just select it on the dash. This also fixed my issue with not being able to shift into low range.
twisted60
Well-known member
- 617
- 250
- 63
- Location
- Jupiter, Florida
Post #5560 I got my line crossed, first pic should be line on LEFT goes to transfer case and line on RIGHT goes forward. SORRY for the mix up.
BenRoberts
Certified insane
- 1,367
- 208
- 63
- Location
- southwest/ohio
added the cargo cover and new ppv.
red
Active member
- 1,988
- 25
- 38
- Location
- Eagle Mountain/Utah
Gathering parts for it's airbrake conversion. 816 is in hibernation for now. m52a2 sitting next to it will become a trailer probably during the summer.
gottaluvit
Well-known member
- 1,786
- 28
- 48
- Location
- Bethesda, OH (AKA: Flyover Country)
Pulled my speedometer cable just to find out it was good afterall. Following the TM can get costly sometimes. So I took the drill and hooked it to the gearbox input drive, hooked the old speedometer that I recently changed out to the cable and it worked (with the drill in reverse) off and on as I wiggled the drill. So I took the speedometer gearbox apart and found four sloppy bushings.
I just put a washer on each shaft and put it back together and the slop was gone. I spun it's drive by hand to make sure it wasn't too tight and it felt a bit tight so I made a gasket to serve as a spacer under the parts that thread it together. Took it back apart and greased it all up and back together. Test drive showed it to work with no speedometer bounce.
I just put a washer on each shaft and put it back together and the slop was gone. I spun it's drive by hand to make sure it wasn't too tight and it felt a bit tight so I made a gasket to serve as a spacer under the parts that thread it together. Took it back apart and greased it all up and back together. Test drive showed it to work with no speedometer bounce.
- 1,450
- 120
- 63
- Location
- Gray, GA
Ouch!
- 5,614
- 2,922
- 113
- Location
- Metairie/La (N'awlins)
There are easier ways to bbq....
Sucks ;-(
Sucks ;-(
Another Ahab
Well-known member
- 17,999
- 4,556
- 113
- Location
- Alexandria, VA
That really bites; sorry for the disaster.
But the way you wrote that was funny (I mean for me, but not for you). It was the progression; it went rapidly from:
- Mild problem to
- Total destruction.
Last edited:
Replacement acquired after 900mi round trip in 16hrs.That sucks.
That one up for grabs now too?
Sent from my SM-G860P using Tapatalk
Another Ahab
Well-known member
- 17,999
- 4,556
- 113
- Location
- Alexandria, VA
You already swapped them out?!
Did you work the NASCAR pits at one time?
https://youtu.be/yOifu4dnCjU
They arent bad. They are meant to be done in the field. I can have one out in around an hour. That includes pulling the bed. Hardest part is getting the bed back on. A transfer case on a 931 takes me around 2hrs start to finish. Nothing to it.
Sent from my SM-G860P using Tapatalk
Last edited:
gottaluvit
Well-known member
- 1,786
- 28
- 48
- Location
- Bethesda, OH (AKA: Flyover Country)
Happy police too!
Another Ahab
Well-known member
- 17,999
- 4,556
- 113
- Location
- Alexandria, VA
Last edited:
Cape Coastie
CWO4 ENG/MSS, USCG, RET.
- 528
- 124
- 43
- Location
- Sandwich, MA
Hey Simp, you are the man! I don't think anyone works on or drives these trucks more than you. Good luck on the next trip. Be safe.
Prob not. Ive got about 4,000miles to do between tomorrow morning and Sunday.
Sent from my SM-G860P using Tapatalk