Atl. bracket question need advise..broke

[hummer4x4guy]

OK, I have a 60 amp alternator and the POS aluminum bracket has broke in the back where the bolt allows the power steering pump to be adjusted.

So I want to replace it with a steel one but I am not sure if parts listed for the 100 amp alt will also fit mine.
Or if anyone knows of the proper part # for a steel alt. bracket that would help also. Tho I believe the part # should be: 12338786

 

[Retiredwarhorses]

The 60amp mount is aluminum...100amp on up is steel. They are not interchangeable.

 

[hummer4x4guy]

Crap!!! Really? This is now going on the 3rd I've had to replace. Its always breaking in the same spot.

 

[hummer4x4guy]

So if I went with the 100amp I could upgrade to the steel bracket. What's the going price for a 100amp alt?

 

[hummer4x4guy]

So what's the special tool used to get the pully off the PS pump? Need to replace that bracket also as one of the holes is much larger than normal. I assume a standard 2 jaw puller to remove but what is the trick to reinstalling it?

 

[86humv]

Make sure you have a rear Alt. bracket or things happen to the aluminum one.

 

[hummer4x4guy]

Yeah I didn't have that bracket before but I do have it now. Tho the holes seem to be drilled in the wrong place. As if they were too far apart. But someone mentioned that it will fit ya just gotta do both sides at the same time or something like that.

 

[auctionaddict]

The 60amp mount is aluminum...100amp on up is steel. They are not interchangeable.

2 of my hmmwvs have 100 amp alts and the aluminum mount ???

 

[hummer4x4guy]

Could ya post a few photos? I have the bracket on order already and will attempt to bolt up that rear support bracket and pray it fixes the problem.

 

[NDT]

2 of my hmmwvs have 100 amp alts and the aluminum mount ???

And mine is a 60 amp on a steel mount???

 

[hummer4x4guy]

NDT are you saying you have a 60 amp alt with a steel bracket on your Humvee?

 

[NDT]

NDT are you saying you have a 60 amp alt with a steel bracket on your Humvee?

Yes.

 

[hummer4x4guy]

Got a part number?

 

[glassk]

There is a pulley if you happen to go with a 300 Amp one,...

 

[hummer4x4guy]

Thanks glass. But for the time being a 60 amp is fine for me.

 

[NDT]

Got a part number?

No. My 1992 dated invoice for the part says "100 amp steel bracket $97.00" But my 1985 dated TMs show the same (aluminum) bracket being used for both the 60 and 100 amp generator. So the steel one should retrograde, unless I am full of crap.

 

[hummer4x4guy]

Where did ya get the part from?

 

[NDT]

Where did ya get the part from?

All American Military Goods, but they are long gone. Their inventory was the beginnings of KASCAR.

I see these brackets on ebay.

 

[hummer4x4guy]

OK. I have seen "100 amp steel brackets" but I've already got an aluminum one on order and when I hookup the rear support bracket hope this will let this one stay around for a good while.

 

[glassk]

TM9-2320-280-24P




has the bracket for 100 amp , part target shows it's a cast iron one, hummer guy parts shows it fits 60/100 amp, you might need to look for kits or parts from one the kit has been installed





http://www.parttarget.com/5340-01-448-4245_5340014484245_12342036.html

http://www.hummerpartsguy.com/BRACKET-ALTERNATOR-60-100-AMP_p_18918.html




13 PAOZZ 5340014484245 19207 12342036 BRACKET,MOUNTING PART OF KIT P/N 1
57K3519.............................





Figure 472. 100 AMP Dual Voltage Alternator and Regulator Mounting Hardware Kit