• Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!

  • Microsoft MSN, Live, Hotmail, Outlook email users may not be receiving emails. We are working to resolve this issue. Please add support@steelsoldiers.com to your trusted contacts.

 

Recent content by fnpurist

  1. F

    Highback seat mod

    There are bits and pieces online. If you buy the mounting bracket kit, it should come with the diagrams and instructions.
  2. F

    HMMWV screws for Tail Light Lens/Cover?

    I'll give that a try except I'll need to call Grote
  3. F

    HMMWV screws for Tail Light Lens/Cover?

    Big help. Thanks a lot. Sent them an email and we will see what happens
  4. F

    HMMWV screws for Tail Light Lens/Cover?

    So you just used a regular self tapping that fit the hole? I thought the original screw was self tapping towards the head and then machine threaded at the bottom to thread into the metal housing inserts. Also, I just installed a Grote front side marker led light and there is a U shaped hole...
  5. F

    HMMWV screws for Tail Light Lens/Cover?

    Does anyone know where to get the weird screws that hold the tail light and front lights to there housings? I bought new LED lights that didn't come with any screws and my old ones are toast and some are missing. I looked in the parts manual and there is no part number, it appears they only come...
  6. F

    HMMWV M998 Battery Cutoff Switch wire route / location

    Yea I had a hole there too with a smaller hole right by it that made me think a cut off switch was installed there previously. The pollak switch I have which is the same one on the other military guys was too tight of a fit for the hole with the switch and 2 big eyelets attached. I'm sure I...
  7. F

    HMMWV M998 Battery Cutoff Switch wire route / location

    I thought about this but wanted to keep the slave receptacle intact just in case. I was wondering if I could mod a slave cable so one side had regular jumper cable clamps so it'd work with non MV's
  8. F

    HMMWV M998 Battery Cutoff Switch wire route / location

    Ok good deal. Where did you end up mounting yours? The only place I could find room and that made the most sense was right above the angled ledge that is above the slave port
  9. F

    12g wire for grounding harness?

    There is some good info on this link for your installation. I'm not positive but I wouldn't think using 12 instead of 10 would be a big deal on this application. http://www.hummerknowledgebase.com/electric/hghi.pdf
  10. F

    HMMWV M998 Battery Cutoff Switch wire route / location

    I started installing my switch today. I got 2/0 wire. Do y'all think this is big enough for replacing the ground jumper and for the additional ground jumper?
  11. F

    hmmwv LED question

    Ouch! I'll definitely be going the route you did then
  12. F

    hmmwv LED question

    Thanks for clearing that up for me. I'll start trying to source one to buy. How much is the proper one that doesn't require any mods?
  13. F

    hmmwv LED question

    So your saying I can't install a led on my green nartron flasher and that I have to buy a new flasher to get my LED lights to work properly?
  14. F

    hmmwv LED question

    Thanks
  15. F

    hmmwv LED question

    Where did you find a led for the turn signal stalk?
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website like our supporting vendors. Their ads help keep Steel Soldiers going. Please consider disabling your ad blockers for the site. Thanks!

I've Disabled AdBlock
No Thanks