Search results

I got 7752 with 38000 miles. Just go to Napa or other parts store and ask for an air governor. There is only one kind that Im aware of and they are used on modern commercial trucks. Its bolted on top the compressor.

Pics later, I got in late....so far ive driven home the following trucks all picked up from GL bases except the TX M944 that Sermis got to his house for me. m35-Oklahoma(towing M109) from Norman OK to FT Riley KS picked up enough stuff to fill both trucks No problems m818 Colorado No...

BTW I looked at #68 Key but dead #70 No key but started Flat tire on outside drivers front rear axle(both beads broke loose but the inside tire is fine, should load ok) #73 Rebuilt 04 Dead #58 No key Dead Dock 31 inches from ground to top, lots of railroad...

I hauled a JD401b tractor(in the back of the Deuce) to my brother in Kansas City yesterday spent the night as his place. Picked up my mep003a from brother and then drove to Topeka to get my new 915a1. Its the national guard base and you enter through a gate on the east side of the base. The...

If anybody is going to gl indianapolis I have a M916 there that Id appreciate a condition inspection on. I dont know if I will fly in or drive there to get it. Thanks, Ross

Soni, Thanks I remember you talking about that. I found one online, no info but somebody has made one. King Pins King Pin Adaptors From 2" to 3.5" EN16 | TRP Parts

very nice thanks for the pics

Im not sure of the kingpin size difference between the m920 and conventional fithwheels. I was wondering if there is enough size difference to make a split, bolt on shell that would bolt over a standard kingpin to make it the right size for the m920 fithwheel? I thought it would be nice to...

It looks like this one but has a twin v-belt pulley on it. The rectangle on the back is the transformer/rectifier

I seem to have burned up the alternator when a battery cable rubbed thru the insulation and shorted out. The transformer-rectifier was smoking. Does anybody know if it can be rebuilt or where I can find another one? Its a Leece-Neville model a001090555 14-28volt, 100amp and a big bolt on...

my 915 and 915a1 share the same key, I got the m919 first and keyless so I broke it so I could use a screwdriver to start it so I cant try one in it.

My neighbor just picked up a Deuce from Ft Leonard wood Mo and the front driveshaft that was pictured in the sale photos(in the cab) is gone. I figured maybe the sprag was not adjusted properly so they removed the shaft. Anyway does he have any recourse with GL for something that was taken...

Youre going to like them for harvest. The only problem might be parking with a full load in the field. If the ground is a little soft and you sink in some you might have to back up before you can go forward. The first gear is not as low as reverse and sometimes the engine cant rev enough to...

I need to look at the map a little more but I might be able to go that way when I bring my m920 back from Pineville LA. My euc hasnt cleared yet and I havent looked the maps over very close but it looks like I could go north from there and maybe not add much to my trip. I might be convoying...

I didnt put very much in and did use the glow plugs but it started right up ran for about 3-4 seconds and died.

My 1009 wouldnt start yesterday after sitting most of the summer. I was thinking like a bonehead and dumped a little diesel down the intake like I would to a gas burner to help the fuel pump. I hit the starter and had the same wt? moment as the engine was racing.

My m919 with 16.00-20 tires runs around 2100 at 65mph. Stock speed is listed as 59mph with 11.00-24 tires(46-47 inches tall)

tacticaltruck, which 916 did you get?

I sent my euc last night, hopefully we can pick up at the same time and convoy towards our homes... Kendelrio, I think it will be in the same timeframe for me and eldgenb, the last of august or first of september.

look at 25, both sides of hood open, shots of the other side of engine but I bet that truck has our engine in it.... 2320 - Trucks & Truck Tractors, Wheeled at Government Liquidation