Search results

It is spec'd out in the LO (Lubrication Order) if I remember correctly...

July 12 — SCMVCC Meeting —swap meet—general meeting 11:00AM— SWAP MEET and SHOW FROM 7am to 1 pm See ya at; AMVETS 14910 Los Angeles St. Irwindale, CA See ya in the mornin' ! UNDER NEW MANAGEMENT and I must say, they are doing a GREAT job...

Only if you have a chair mounted to the 5-Ton Wrecker inspired mounting plate I sell and if said chair is OCCUPIED . :-)

...it will, it will............................

Some men, and women, have more money then Carters has pills. If they want it, or perhaps NEED it, nothing will stand in there way. Additionally, there is no doubt a bidding war can get very personal w/ some folks and if funds are easy to come by, even come high water, they WILL "win" ...

I have addressed the front and rear of my 5 Ton. Yes I sell parts to do some of this stuff. Up front I pulled the cheesy lightweight winch-keeper-channel and replaced it w/ a heavy piece of structural steel channel, something like 10" x 2" Steel channel to give me a frame to attach a...

Months ago when I went to Arizona I stopped at a Holiday Inn for the evening and when I came out in the morning I found both of my nice, new, round, green, convex rear view mirrors were ripped off my truck, literally, ripped off. The scumbags bent the "L" brackets back and forth a hundred times...

I do believe a 20' container HIGH CUBE is 9'-6" I do believe a 20' container STANDARD is 8'-6" Do our own research to be sure.

Well, I hope for more pics cause I can't see the method of the madness. I thought all's you needed was a solargizer to do what your doing....??? What model Solargizer are you waiting for? That might enlighten me.

Thank U Davis, that is close to right I am sure, but factory calibrated and certified gauges might work a little better. It boils down to cost certainly... I appreciate the input!

I have had this thread on mind in-so-much that I want to figure out how to qualify a "Known Good Temperature Gauge" . Input?

Thank U An/Arc!

M916 Driver Side 5 Ton Box The PS was done, now I have the DS done. Yes I will sell the brackets. They are made from .5" thick steel, there are 4 pieces, no they can not be cut cheap. I have to price each time but expect $255 per side approx., plus ride. No welding to frame required. No...

TM 9-2320-272-24P-2 PDF PAGE 220 perhaps.

I bought two of them on Ebay 2 weeks ago for $16.00 EA. look up the P/N in the TMs and punch it into Ebay to find it. So you removed that little thing and went for a drive and found out the brakes didn't work good w/o it?

Field Maint manual 2 PDF pg 834 right? I do not see anything that says START ENGINE. Open petcock and drain off any water, probably matters not if running or not. Safer not running. Remove the whole shootin match to replace filter. Fill w/ fuel BEFORE you re-attach things and you will...

I have upgraded charging system kits complete and new I would consider selling.

Your going to open those plates and find that block FULL of crap I bet... Take pics...

I am NO EXPERT, at all, but after reading this, if that were my truck, while the radiator is out, I would disassemble the balance of the cooling system and CLEAN / FLUSH IT ALL. Even if you had it open before, open it again and FLUSH IT ALL, forwards and backwards AND THEN DO IT AGAIN. The...

Look up Clearance lights code, FMSCA I think it is. I believe I see you need clearance lights ; A 3 Light ID bar in the rear. (over so many inches wide) Side clearance lights. Rear Clearance Lights Arguable, Amber clearance lights at front of flatbed. Load in your Reflective triangles (3)...