Search results

Ah HA! thank U!

Stuntmog can you tell us what "CPL" stands for? My CPL=709, any idea on weather or not I have plugs or actual piston cooling nozzles installed ? Engine dated 02-92

You betcha Al, at ERIKS . Please tell Erik I sent you. Hit all the bolts w/ PB Blaster, Pull the bottom 2 Muffler guard shroud bolts. Slightly loosen the top 2 (just a bit). Start at the top pipe w/ a 9/16" Deep on an impact at the clamp. Remove top pipe. Pivot muffler guard up pivoting on...

PB Blaster, now sold at HomeDepot is REALLY GOOD STUFF. It is not mandatory but if you squirt just a taste perhaps a week before and every time your close to it, letting it seep in and work will turm you into a believer. It does not take a LOT! Just enough to wet the threads. You can...

Well, I started at the top AND DANG GOOD THING I DID. The mufflers uppermost flange was 50% rusted out! Not long and that top pipe section would be falling onto the roadway, my luck in front of a motorcyclist so off it all came up to the offending joint. I ordered up new gaskets and I am...

Did you make that recording? Where did you get the clamps from? Pics? TIA!

Guys I have a pretty good exhaust leak going on. While it looks fairly straight forward in repair procedures I wanted to ask a couple of q's perhaps of those whom have been there done that before me. The Magenta colored arrow points to the area where I have a leak. It is from here back where...

I think I would try to make it stop before go... but; The TC is not in NEUTRAL correct? The trans has oil in it correct?

If you make a way to pressurized the air system w/o the engine running you can sometimes do said and hear a leak because the engine is not running. I added a 1/2" brass tee at a PRV that is before my Air Dryer, adding in a shrader valve so I can just connect a shop air line to the truck and...

I added a pipe wrench to my tools for my M925A1. I was rummaging through mountains of ISO beds cut off M927 trucks heading to the scrap yard and found this puppy totally rusted up, not one smidge of paint left, only a rusted hulk. We took it home and massaged it back to life, re-christened the...

I will try to come w/ my M925A1 . I would love to convoy but that word is VERY BAD if used in the wrong way w/ a patrol officer IMO. The way I understand it "convoys" w/ the exception of legit Military, are "illegal" and should something bad happen and a couple guys were to say they have been...

Thanx for the comment and critique' CT ! Glad to meet ya btw... Did you see the gussets, the deals w/ stars cut into them inside left and right? The 7" tall triangles ? The drops and gussets are .5" thick too.

Very observant FN! I designed a hitch, had the parts water jet cut and bolted them on along w/ a weld on cross bar 16,000 rated and it came out quite nice. I'm not ready to release anything yet, a minor hickup to remedy. I will have pics when I am 100% w/ it ... Some of the guys at...

Sounds like a plan. I just went to Bad Karmas' deal and had no problemo draggin' a 22' Warrior trailer in behind the M925A1 .

Well, you found "a" problem, how about fix that issue and eliminate it, needs to be done anywho, and see what happens?

What happens when you do a COLA test?

When you drain your air tanks, the 4 valves on the PS do you get air out of all 4 ports? Do you get air, high pressure out of the PS rear gladhand? Are all gladhands valve or capped? I am NO PRO by far FWIW. I would like to know what you find ...

My M925A1 is off about 8-9 mph as well. It is pretty much standard on these trucks I am told. Get a GPS and look at your spped with that. my new magellan says I roll at 68.3-4 MPH on a flat road, pedal to the metal. It is more fun at about 50 real speed though...IMO

If you start the truck and touch nothing letting it run for maybe 5 minutes what does the primary and secondary air pressure gauges read in PSI ?

When shes done roll her over to Monrovia ! I have an M925A1. LVAD Low Velocity Air Drop right? Did she do a LVADR? Low Velocity Air Drop Rollover