• Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!

  • Microsoft MSN, Live, Hotmail, Outlook email users may not be receiving emails. We are working to resolve this issue. Please add support@steelsoldiers.com to your trusted contacts.

Search results

  1. R

    M1165 Humvee now recovered! from Scottsdale AZ

    So sad to hear this. [emoji22] Sent from my iPhone using Tapatalk
  2. R

    Is it possible for water to get in my front differential?

    If the gears were water contaminated it would be prudent to pull the cover to thoroughly inspect the gears and bearings Sent from my iPhone using Tapatalk
  3. R

    2 Man Cargo divider

    Parts TM shows the bracket layout. Basically two brackets to the B pillar and two to the floor. Sent from my iPhone using Tapatalk
  4. R

    Anyone use headlight polish on the gauges?

    I used the low-tech method of toothpaste polish followed by wax. It worked pretty darn well for my gauges Sent from my iPhone using Tapatalk
  5. R

    New Supercharged and Intercooled HMMWV kits!

    Interested Sent from my iPhone using Tapatalk
  6. R

    Leak , where do I begin looking

    Fuel tank bung is typical… Replace, check ultimate well nut thread Sent from my iPhone using Tapatalk
  7. R

    What have you done to your HMMWV today/lately

    Finished adjusting shims for camber/caster today. Removed the following from RF. Put 2 thick shims back on RF bucket to get zero camber with max caster. Also took the opportunity to replace front tie rod ends. Sent from my iPhone using Tapatalk
  8. R

    M1165A1 style top

    I’m curious how the availability is for this style top and center support structure. Any suggestions on suppliers and relative cost these days? Sent from my iPhone using Tapatalk
  9. R

    block heater install...not too bad

    Did the same on my 998 a few years ago. Glad to hear it went well. Very handy in cold weather. [emoji106] Sent from my iPhone using Tapatalk
  10. R

    6L80 in my M998

    Best to service/rebuild before installing anyway Sent from my iPhone using Tapatalk
  11. R

    3L80 Tranny issues

    Likely an internal failure. Probably prudent to drop the transmission and inspect/rebuild accordingly Sent from my iPhone using Tapatalk
  12. R

    What have you done to your HMMWV today/lately

    Omnia Warehouse Hummer H1 Windshield Seal Set 2 PCS H1 HMMWV M998 1992-2006 12338941 12338860 5330-01-209-5997 Seal, Windshield Glass LH and RH 12338941 2pcs/Set $63 Sent from my iPhone using Tapatalk
  13. R

    What have you done to your HMMWV today/lately

    Gaskets are inexpensive… well worth changing if old Sent from my iPhone using Tapatalk
  14. R

    Mep831a keeping the lights on.

    The 802A is great for my home. It is lightly loaded with our typical draw but has enough power to operate our heat pump/gas furnace. Added bonus when the pump kicks on it burns off the wet stacking[emoji106][emoji91] Sent from my iPhone using Tapatalk
  15. R

    Mep831a keeping the lights on.

    Manual transfer or ATS is the way to go when you have time. [emoji106] Murphy’s Law. Since I’ve installed an interlock with my MEP-802A we have had only brief power outages. [emoji1696] Sent from my iPhone using Tapatalk
  16. R

    MEP-802A Rodent Proofing

    Yep, bottom needs to be screened as well. Looks fun [emoji107] Sent from my iPhone using Tapatalk
  17. R

    MEP-802A Rodent Proofing

    Yeah I have no desire to completely rewire the set. I just had to rewire the main output wires this season due to faulty installation. Rubbed through… Sent from my iPhone using Tapatalk
  18. R

    MEP-802A Rodent Proofing

    There are two holes under the batteries for drainage but blocked by the batteries themselves. I still need to look under the main engine rails Sent from my iPhone using Tapatalk
  19. R

    MEP-802A Rodent Proofing

    Finally made time to wire screen the side vents. 1/4” screening with zip ties. Also have moth balls placed in various interior spaces away from HV electric or moving parts. Sent from my iPhone using Tapatalk
  20. R

    Towbar identification assistance

    Much appreciated! Which adapters should I be looking for that are compatible with the HMMWV/M998? I gather it’s: Clevis NSN: 5340‐01‐046‐ 4770 Which has 3/4 and 1” pins? Sent from my iPhone using Tapatalk
110,897members
165,315threads
2,326,244posts
1,515online users
Top
✖
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website like our supporting vendors. Their ads help keep Steel Soldiers going. Please consider disabling your ad blockers for the site. Thanks!

I've Disabled AdBlock
No Thanks