Search results

There are like 8 different sizes of flywheel housing sizes. Cummins mainly uses 1, 2 and 3. I have seen 0, only once and 4 only once, not on a C series though. That's why, if someone can post an ESN, I can find out what the gooberment spec was...

Nah, the gasket on an 855 will push compression out the sides before putting pressure in the cooling system. Is the top tank real hot and the bottom tank on the other side of the lower rad hose cold? The reason for checking the temp away from the outlet is that if the w/p is failed and no...

This is for the NHC, p/n 3014979 MR - HOUSING, FLYWHEEL...(More) Engine Family: NHC-250 SAE #2 Wet Flywheel Housing With Offset Mounting Arms Can be Used With Small Cam Engines Only For Use on NHC-250 Engines...

Give me an engine s/n and I can tell ya. Most likely a #2, but give me a s/n to make sure.

Cummins FSOV Specs Here ya go....Want me to sticky this?

Sorry, just saw this. No. there are 12 and 24 volt FSOVs. The solenoid has two coils in it, pull in and hold in..... A, red wire, hold in......B, white wire, pull in...C, black wire, ground. Pull in is wired to the crank circuit, some OEMs wired to the starter solenoid, this will pull the FSOV...

"Also was curious to see they list fuel burn of roughly 13 gph. That would mean at steady 55 mph, you're only getting around 4 mpg. I think most feedback I've seen recounting long trips claim fuel economy was 8 to 10 mpg." Because it is industrial and a fire pump. Automotive, Industrial...

For your reading pleasure!

For your reading pleasure!

24 volts has nothing to do with it, wiring is wiring. A DVOM is your friend. What is the issue?

You DO need to lay a thin bead of silicone based adhesive on the pan rail joints where the rear seal carrier and gear housing meet, just on the block side, nowhere else. Don't use rubber based silicone, the acids in the engine oil attack it, turn it to goo and you will have a leak again.

Used to, quite often. The SCMVCC was asked to participate in them all the time. We would pull up, get into position and all the people around us would be dusting and waxing their junk, I would woop out a rattle can and start touching up! They loved me :beer:

Where is the leak starting from? IIRC, the heads are oiled at the front rt side....could be mistaken, old age ya know! so if it is on the fuel pump side, it ain't a h-gasket. Also, a leak always starts out high and ends up on a lower portion of the engine, look higher for the point of origin.

32 foot lbs. the compressor also needs to be timed or it will be noisy. there is a hash mark on the comp drive gear. that needs to be aligned with the notch on the compressor mounting flange...on the compressor...the hash mark will be at the 300 position when looking at it from the front. You...

The studs into the gear housing are coated with a locking agent from Cummins. No other locking agent is needed on the compressor mounting EXCEPT for the hardware that mounts the two rear, bottom support pieces, 6 capscrews in total, two into the bottom of the comp from the flat plate, two from...

It isn't a Cummins part, it is what the OEM uses as the discharge line. Measure the line and go to your local industrial hose outlet and they can make it for you out of DOT air comp discharge braided stainless with the ends you need.

And, if it's an 855, it's easier/faster to remove the complete accessory drive/comp/fuel pump as an assembly and do the components on the bench. just make sure the timing is set when you go back together.

If it's a C series, make sure you loctite and torque the compressor support capscrews into the block, support block AND the compressor or you will crack the gear housing if they come loose. A fun job, for me!

Uuuuuh, this thread is 3 1/2 years old. You might want to try and PM him

Top stop and non top stop can be used together. No "pop off" pressures in them, that is generated by cam lift. You just need to use the outer base circle method to adjust them. post the p/n on the one on the right and I can tell if they are NHC injectors. Remember, there were big cams in use so...