Search results

This should be a redundant question - not least that the Tech Manuals posted on this forum at the top, explain suspended towing in the M816 Operations Manual under Normal Conditions, BUT if you are paying for a tow truck then HE should know or be able to ascertain any and all requirements for...

Ok, I'm going to play the OP card here! I know we have mentioned the whiffle tree before - maybe "Wrecker wish list of mods" thread.... but that little ring that is hanging down from the middle of it - purpose anyone? I think (as in - my opinion) it is to hang on the hook, which then has the...

Level Wind Pros and Cons Appreciate that - I just threw that in as it had been previously discussed and the principle is the same - just in the opposite direction (if the front has a level wind). Not necessarily in order - but here is a start for you to consider... Level Wind (with...

Wildchild - thanks for revving up this post again - I needed to add a postscript anyway. Hope you got your answer for the 'one-man operation'. One alternative [ if you think you are going to get stuck - and will need 'self recovery' ] is to back away from a fixed anchor, paying out cable...

Yeah - I have wondered if replacing the A1 valve with a 5 port double diverter valve would be viable but the [/SIZE]real-estate being premium may not allow elbows on the left side (facing forward) of the valve... as an aside, I am awaiting a logsplitter valve (scratch built for neighbour - 3...

Thanks DS. Certainly a load more (read Total) experience your end of the stick! I found the TM pic of the A3 setup, though I don't have the parts section to see if the valve on the A3 is the same as the A1/A2 with a plug removed or if is is a larger valve with more ports. Anyhow, the physical...

Thanks DS... however wouldn't 'piggybacking' a second diverter valve where you suggest pick up the highspeed pump output not the lowspeed one if so - would this be a problem? I was hoping to avoid another valve, just going with 'T's' but even on the farm tractor, I have to throw a lever before...

I Goobled the above and only found reference to an M915A5 which does not look like a Freightliner - it has double round headlights. There is a reference in an Olive Drab article to a 916A4 in the 915 section, seperate to the 916 section - a typo I am thinking... Not sure if OP needs a...

Thanks John... Trailer needs pressure to cylinder controls on trailer goose neck - operated from the ground, adj gooseneck detachment point. The idea I am following is from "remotes" I have on a farm tractor, that are pressurised by selecting a valve that does not 'kick out' while waiting...

I think you need to list your needs/likes and do pros n cons for each. Do you need a live front axle - this will lift the fifth wheel. Do you want a full on military look or a militarised civi truck - M915... either CCC or Freightliner will be cheaper for parts. Likely that cruising speed will...

Further to these threads: http://www.steelsoldiers.com/showthread.php?127106-M916A1-Little-Stuff http://www.steelsoldiers.com/showthread.php?123032-M916A1-w-w I wanted to fully understand the schematics of the PTO hyd/winch system with the plan to add the A3 wetline kit for trailer hydraulics...

I was going to comment on the winch loading 'till I reread John's comment - I missed the "well" on first reading... BUT anywho... I couldn't find the TM in the 'Technical Manual' section of the forum. TM 5-2330-378-14&P - did find it online a while ago but I don't have good enough internet to...

light turquoise like ! This colour....

Hate to correct, but actually DPG - stands for Deep Bronze Green, often called Military green and was used on most FV's from the factory (with a few exceptions) made for the British Army, which were then over painted camo or OD etc., once in service.. Next question - what is the name of the...

Here is a diagram of the inter-relationships of the parts, inc seals and bearings for the trolley frame/sheave frame connection. Also shows, from Post #4, the "Towards" reference relating to removal of the needle roller bearing. NB. There is a machined recess that the washer #28 sits in, which...

They are pretty rare everywhere except in the UK. Total production was only around 2600 - some went to Oz, some Belgium and some Kuwait. The Brits left a few in Belize and also Canada.

Needle Roller Bearing Restoration - Trolley Rollers #20 Yes - this is possible and will save megga bucks and is appropriate for this situation as the trolley rollers #21 are not exactly rotating at thousands of rpm. With a 300' recovery, they may trundle back and forth a whopping 4 times across...

Corrosion in Trolley Frame - Blocked Drain Holes Forgot to add this pic showing the corrosion to the inner bore of the trolley frame due to blocked drain holes. Potentially this could be too much grease being pumped into the ball bearings below, forced up past the felt seal. It might be worth...

Ordered pivot shaft bearing from Fastenal today. Around $25 ea. I ordered a spare in-case anyone else needs one and doesn't have access to a local store. Don't even bother with NAPA - their bearing books don't go that small. Added captions to pics in post #4. Was in the middle of doing...

Tips - continued + pics OK - good news/bad news on the broken pivot shaft #16: No luck yet on finding a replacement however on closer inspection of cleaned parts and test reassembly - there is a shoulder on the shaft that draws tight the shaft with the large nut on the bottom #17, so NOT...