Search results

This makes me want to rethink my crew cab build. Very nice. What bed liner brand did you use and what mod on the front axle for those wheels/hubs?

My replacement line came in last night, hadn't had a chance to check it out. I'll post up when I swap it out.

The part #'s match up to the tm part#s pretty good. The line is 7w0367. $21 plus shipping. I ordered injector O-rings for my truck as well. The calculator on there page automatically puts ups on with a crazy shipping amount, but you can change it to usps for much better rate. Was $7 shipping.

Its the stock one. offroadeq.com. I ordered some other items related to the 3116 as well. Figured I would replace mine and try to avoid that failure.

I ordered that line yesterday for $21.00. Got it from off road equipment parts out of TN.

With the right insulation put in it would work fine. Reflective for the roof and floors, then some good lizard skin or heavy butyl. But for me, I am not looking for arctic temps, but if its 90 outside and 70 inside the cab, it would be much more comfortable. I know some folks have gone the...

I have been researching options for this as well. I have no emotional attachment to the center console I have and thought about using a universal kit to fit the ac. The bracket of course is the main item of concern. I was planning on making a carbboard template of a bracket setup for both side...

I wish I had bmp, even a leaking one lol.

Well the ctis overspeed went away. I did a cycle of airing down to xc and then back up. Then the next startup cycle the light did not return. Now of course I'm getting air venting out the front gladhand, so looks like I will be replacing those check valves like everyone else. I will still try to...

JkCondrey: Wont go over 50? What is the highest gear it shifts into? Have you checked for any transmission codes? When you replaced the TPS sensor, did you calibrate it? It lists all 7 speeds and does shift into 7. I have done two cycles of the tps resetting(5 master on/off followed by a...

I went through the TM for the ctis troubleshooter. I am having the ctis overspeed light come on while sitting. The setting is to hwy and all tires are inflated. As you move off, the light goes off on the dash, not sure what speed, seems to do it whenever. I have seen issues with it NOT coming on...

I also have the telescoping jack leg for a 105 trailer. Works great. Swivel and jacks up/down well. $30 if interested, text me before I drive down Friday8282893192

I got the new parking valve and installed it as well. Just swapped the fittings over to the new one. Came with a blue top cap with the easy attach push bottom fitting for it. Again much better than the old roll pin deal.

Seth, did you rebuild the primer pump or use something else?

97' 3116 LMTV. If I pump primer bulb, it takes about 10 pumps to get "solid" feel. Go to crank up and get tons of smoke for 30 seconds, up to 45. I usually only push the starter about 5-10 seconds max. It will occasionally sputter through the whole 30-45 seconds before finally clearing up in a...

I just spent some time replacing the trailer valve and have ordered the park valve. I will point out the Haldex recommended part # for the aftermarket is KN20035, as the replacement for the tm # n30262. I have seen the # listed kn20021 in some places, but the tech line and the website specify...

Well I got the trailer supply valve in and installed. Quite easy to install, just mark the lines and fittings, remove and swap then reattach. Easy enough I have ordered the Park valve too. I know a lot of folks like the new single piece unit, but I just choose to stick with the original setup...

Well, I called Haldex and the part # listed in the tm's is not orderable by the civvies, but the tech recommended part # kn20025 as the replacement for the common folk. I just ordered one and will chime back on it after its here and everything is pulled out of dash for comparison. Not that the...