Search results

Page 12 of the supplement talks about voltages and it says approximately 0.5 volts closed … signal voltage increases to greater than 4.5 volts at wide open throttle. Thanks for the help, I have another TCM here same year as mine I can pop in tomorrow and see. Sent from my iPhone using Tapatalk

1 of the first things I tried was hitting all connectors with contact cleaner, they all looked bright and shiny. Just got back from test run after adjusting TPS, I set it at .502vdc. It started out good but went into limp mode after warming up. I tested TPS again when I got home with everything...

Was able to pull codes today (used different jumper) . New code pooped up, 87, Did some testing on TPS, I think retired warhorse mentioned to check. With glow plug controller disconnected I got: 0.7vdc (no pedal) - 4.49vdc (pedal to the floor) from wire 355B 5.02vdc from wire 350C Manual says...

Codes were 38, 85 & 86. 38 torque converter clutch 85 undefined ratio error 86 low ratio error I’ve changed the TISS and TOSS no change. When everything is cold transmission runs normal RPM to MPH. After it heats up it goes into limp mode 2nd gear only. When hot it won’t move if I shift into...

Yes, truck level, warmed up and ran thru gears. Sent from my iPhone using Tapatalk

Yes, that’s where I got the codes from, what I don’t see is what to check. Or maybe I just don’t understand what it’s telling me. Sent from my iPhone using Tapatalk

I’m getting codes 38, 85 and 86. Where to start ? I unplugged the external connectors and cleaned with electrical contact cleaner. Where next ? Issue is she’s going into limp mode. I checked battery voltage, 14.37 coming into rear battery, reset CB, repaired 2 wire that looked if’y, checked...

Has anyone found a good fitting floor mat for front and rear ? If not what are you using ? I have a humvee with no floor cover at all, I'm thinking of using rhino liner sprayed on. Anyone put sound deading mat down then cover with rhino liner or ?

I’m trying to remove the extension piece for wiper, I’ve removed the set screw but they don’t want to move. Am I missing something ? Thanks Sent from my iPhone using Tapatalk

I’ve only googled 1 so far and yes it available Sent from my iPhone using Tapatalk

Thanks, I’ll start looking for these items Sent from my iPhone using Tapatalk

Thank you War Horse, could you direct me to the Tm ? I’ve looked in all the [emoji769]’s I can find but no luck. I do have the piece that fits inside the lower section so I assume all I need are the covers that must hold the top to the support ? Sent from my iPhone using Tapatalk

Need help locating B-Pillar missing parts. Anyone know where I can find them ?

I've looked in every Tm and just can't find the missing piece. See attached pic. Need to source replacements. I'm installing a 2 man hard top from a M1152A1 on my M1152, haven't taken my M1152 apart yet until I source parts. Thanks in advanced.

It’s a 200 amp Sent from my iPhone using Tapatalk

TM says 700 but says nothing about A/C on or off, do you set RPM with A/C on ? I'm in Florida so A/C is on 90% of the time, idle is 700 now at idle but put it in gear and turn A/C on and she drops to 650. Not a big deal just curious. Thanks

Jupiter, PBC

Thanks all that answered. RWH, no black smoke and plenty of low end power so I guess it's working,

Thanks all

I have an 1152 6.5TD, looking for parts break down of turbocharger, pictures of disassembled unit, troubleshooting info etc. I don’t think mine is working, I test drove it with doghouse and heat shield removed, before test drive I confirmed the waste gate moved freely. Waste gate never moved...