Search results

Years ago I did this because of the weeps . I replaced all the core pugs while it was down , hoses , clamps , starter relay . Not one issue with new style gaskets . Positively check the heads to be sure they are flat . Somewhere , I think I still have the tool to torque the bolts . I lend it you...

I have added the resistor from another sender to the needed sender many times . Building Hot Rods . It’s rather easy , just have to match sender and gauge ohms to read correctly . As is try to locate a sender for 37 Chevrolet to use 2 5/8 gauges from a C70 , really was a super easy fix . PM me...

Ok , I don’t have a sender for that . What’s wrong with the one you have ?

The AMP meter is toast as mentioned , the firewall plug is more than likely crusty also they are not in the best location . Remove it clean the connector , look closely at the main power connections ( Amp Meter ) in and out , 90 percent change they are cooked also . Remove these terminal ...

Well help me with what a 38A1 , is . I’m kinda stupid , on the numbers .

Switch it to later NP435 and 205 , 208 or 241HD , all are good . 205 is all gears , 241 is the lowest ratio . I switched mine to 4BT and NV4500 , it took me 5 years to locate all the parts to swap it over . The diesel had to have OD or only drive 55 MPH . I’ll contact a few Buds and see what...

That’s a fabed bracket , the bracket shown by Bob is the best steering bracket you can get , there is a later one that is junk . The early one posted uses the reverse rotation box and will make the later trucks feel as if the steering was junk after a swap to early stuff .

I have an extra sender if needed

NP 435 has 2 output shaft lengths , one for a 203 case and one for the 205 , 208 , 241 . All are 23 spline . Do not loose the coupler between the trans output and case input , they are no longer available and are reaching untouchable costs to purchase . I recently sold a complete change over for...

Sorry for the delay , I just flipped the caster shims that are on your axle now . I also added power steering at same time as changing wheels . So no answer if it was better before or after shim swap . I do know it was **** better after Tire and steering swap ! Thanks again , sorry for the delay...

I did mine years ago. Wheels from Freightliner , 6 Lug 8x22.5 . 22.5 tires are a dime a dozen . tubeless also. just have to change caster shims so it will drive straight with radials.

Da Gimp is the best !!

Flame Heater Disconnect the flame heater outlet going to the intake with the engine running . It will be flowing a large stream of fuel if it is leaking through . If no fuel that is not the issue . I purchased a new one from Memphis it leaked through just as bad as a old one , Memphis send a...

Hyd. Head first also, then Flame heater . Flame heater will majorly fill crankcase with fuel. I found this the hard way !

Ok , sounds good !

4BT Turbo I can't remember what turbo I have . It has only Cummins reman numbers on it . It was off a 12 valve . Early 6BT, I am thinking a 1992 . It works great . I changed fuel pin , turned up star wheel and and did not turn up the full fuel screw . No injector mods at all . I am getting 26...

HX35 turbo I ran the big turbo for a bit on my 4Bt . Ended up with a 30 series turbo . HX35 took to long to spool up and didn't seem to make anymore power on the top end than the 30 is now . Look at 4bt stuff on Flee Bay there are a lot of parts and complete motors for sale in Cleves , Oh. I...

Not related to your issues , my 4bt in a Dodge is getting 26 MPG the 318 gas got 9 MPG . Hey Gimp , back not much better , just holding my own. Good ole Duke Energy , breakin it off in me ! Stole about 200K in retirement funds after 35 years of employment !

4 bt Flywheel I have the 4Bt installed in my Power Wagon now !! Not sure if you tried , but I am thinking GM uses 2 different length Throw Out Bearings , maybe need to use the longer one of the 2 . Also did you use the 4BT GM flywheel ? They are super thick I am thinking also 2x as thick as...

installing a 4bt into a 79 Dodge Power Wagon , weight is near 750Lbs . it should be fine with 4 inch lift springs. I used 6 bt 1st gen springs in mine. There pre made kits to install 4 bt into Gm trucks . Oil Pan clearance is the big issue that I see .