Search results

OK, The MEP-802A and MEP-803A units. Start a thread about the 804

Howdy, MEP-802/803 ONLY starting checklist Quad winding fuse installed Ground is in place and wired After the unit has been checked out for operating 2 x 12 volt batteries fully charged phase selector set for 120/240 (or whatever your using)(behind control panel) multi-meter to verify if gauges...

Howdy, If it is a newer, M1101, M1102, LTT-TQG Surge brake assembly Military part to civilian counterpart model Titan/Dico Model 6 hydraulic brake actuator. All the parts for repairing and fixing. cylinder, cap, breakaway,, shock, spring clip etc..

Howdy, It seems the MEP-8xx fuel/water spin-on filter is put on by King Kong. Use a good filter wrench, strap wrench which fits and pull really really hard. It does actually come off. Every MEP-802 and MEP-803 I have come across has had that filter way to tight, and dry. This is usually what...

Howdy, It depends on what model of trailer (Power Unit) A PU-798A (MEP-803A on a LTT-TQG (Similar to M1102)) Shows to be 71.25 inches high

Saved for further additions Sticky Time :grin: I would also suggest that you help support Steel Soldiers and become a member here.

Howdy, All the manuals you will need to do anything with your units are here on Steel Soldiers. MEP-803A, All the TM's you need All the manuals for the MEP-802, 5KW Generator and MEP-803 10KW Generator MEP-802A and MEP-803A manual information MEP-802A manuals you should have TM...

Further additions 1st Important Unit check! Do this before starting unit Quad winding fuse mod on page 29 Reset Manual here PDF page 29 has the MEP-8xx 5kw and 10kw fuse mod. It also has the ME-8xx 15kw and higher fuse mods listed too. More info MEP-802 and 803 Main generator tip simple...

Howdy, MEP-802A ONAN DN2M 2-cylinder engine (Lister-Petter LPW2) Liquid cooled diesel, aluminum housing MEP-803A ONAN DN4M 4-cylinder engine (Lister-Petter LPW4) Liquid cooled diesel, aluminum housing MEP-802A Filters List, MEP-803A Filters List Oil Filter Spin-On (FILTER ELEMENT,FLUID...

Howdy, The parts units are still selling for big money. Are there that many people with home radar systems?

Howdy, Hopefully, someone which has installed a bulkhead fitting responds with the proper torque.

Howdy, Before you get to carried away. Wait until the unit arrives. The MEP-803A is not really loud in comparison to generators which you might have heard running. A lot also will have to do with access to each of the panels. Maybe just a lean too roof over head. Welcome to the forums. If you...

Howdy, Welcome to the forum. I also would like to say thank you for the information in your post. It makes it easier for everyone to make a informed decision about what you need. I see you have read the forums. By what you have stated, I can see you have all the manuals, and have read them. You...

Howdy, You might not be done. You might of had some gelling, some wax in the filters. BUT, it sounds like you have water in your system. Condensation is a problem with weather changes. Best to keep the tank full, and treated for conditions. Make use of the fuel drains for water.

Howdy, It looks like the unit he purchased is a Sierra 18-5899 Oil Pressure Sender.

Howdy, I have the Noco G7200 and use it with a slave port connector. I also use it in 12v mode to charge the 2 batteries by themselves to make sure they are even. And many other 12v batteries in other vehicles. The 24v charging is good to keep them maintained. Its also good to check them by...

Howdy, Take a look through this thread Picked up 3 MEP-802A gensets and will be documenting making them all runners here Peter went through the units and documented all the things he did. Very informative with the soaking, moving, soaking, timing etc.. to free them up.

Howdy, No company will send you the plans. Not until some money has exchanged hands. You ask for samples and pictures of structures built. They can all be called pre-fab and all shipped from Pittsburgh for all you know. The important portion is going to be the local contractor crew to erect the...

Howdy, A lot will depend on what part of the country you are in. Take a look at a local airport. Look up at the eaves. Most companies put there name plate there. Butler is one name which comes to mind. I would expect any out fit which builds the structure will account for location, (Maine) and...

Howdy, Go to any industrial business. Say a mall, a 10 story office building, a large truck service center, etc... Large equipment which use motors, are more likely to be 3 phase. (and to mess with you more, there are some different 3 phase methods) and the phase rotation needs to be the same...