Search results

Howdy, Any surplus generator should be fully loaded to 100% for a few hours to ensure its operating properly, and to clean up the exhaust. Working some MEP-802A/MEP-803A units on a military surplus load bank

Howdy, All the manuals you will need to do anything with your units are here on Steel Soldiers. All the manuals for the MEP-802, 5KW Generator and MEP-803 10KW Generator MEP-802A and MEP-803A manual information MEP-802A manuals you should have TM 9-2815-252-24_____ Diesel Engine...

Further additions Spin-on fuel filter not coming off MEP-802/803 Filters Listing Break-In Oil Low hour units here Battery info here 24v charging info here Fuel return line info here MEP-8xx series engine paint MEP-8xx series Coolant overflow cap MEP-802/803 Fuel pump MEP-8xx...

MEP-802A ONAN DN2M 2-cylinder engine (Lister-Petter LPW2) MEP-803A ONAN DN4M 4-cylinder engine (Lister-Petter LPW4) MEP-802A Filters List, MEP-803A Filters List Oil Filter Spin-On (FILTER ELEMENT,FLUID NSN#2940-01-154-5127 ) Prefer WIX 51374, Napa 1374, works also(WIX 51348, NAPA 1348 )...

Howdy, In the United States, power is 120/240 volts, and 60Hz. UL = Underwriters Laboratory Things which are sold to consumers in the US have a UL sticker. That means it was subjected to variables to qualify for a UL rating. The official UL rating means the product can withstand a variance of...

Howdy, I have most of the accessories for my PU-798A (Mep-803a on a LTT-HC high mobility) Pictured; slide hammer slide rod driver/puller rod, with rod knuckles ground rod clamps remote 55gal/5gal fuel pickup adapter aux fuel supply line 6awg braided copper ground carbon dioxide fire...

Howdy, It is the bar at the bottom right. It is known as the neutral bonding bar.

Howdy, The temperature gauge is deceiving. There is not a lot of marks or space between the 200 to 240 temp readings. My unit was wet stacked. The entire unit had to burn off the wet stack goo which had gotten all over. I really should have taken the muffler wrap off and cleaned that whole...

Howdy, Without doing a onsite inspection, you really need to look over the pictures really good. GovPlanet knows that if it runs, it will bring a higher price. I would say the staff will do little tweaks, such as adding batteries, and such. A video with it starting and running gives you an idea...

Howdy, I suspect that is why it only brought $800. Some members here purchased units like that. They drained the oil and got all the oil and about a gallon of water. Of course it also depends on how long. Onsite inspections and "does the motor turn?" could make a big difference.

Howdy, So, do you have the cable in place? Did you trim any of the length off? it looks like you could fit it, and then trim the black covering back to where you need and simply cut the wire to the length you need. Is the knob all black, or does it have that bright red button?

Howdy, You might have already found it, but here is the TB which covers this. TB 11-6115-741-24

Howdy, It sounds similar to another member here which had troubles with the S-1 start switch. At some point in time, somebody replaced the S-1. But, they did not get all the pieces back in place. A few of the wires then have jumpers over to another screw. Anyway, he ended up disconnecting all...

Howdy, As others have said, get a hand meter and check what the frequency and volts are at the lugs. Motors start and run better on 240 volts and 60 Hz. If you keep going and the Hz is way off, you will kill your pump.

24v charging thru slave port

Howdy, Fuses? We don't need no stinkin' fuses :naner: MEP-802A/803A gauge lighting

Howdy, It really depends on the distance too. I have 2 units for sale here in Virginia. 2009 MEP-802A with 60 hours for sale 2009 MEP-802A with 561 hours, with LTT-TQG trailer. ( PU-797C ) Tan Both units are for sale and are ready to go.

Howdy, That is normal. I have a load bank thread Acquired a Military surplus load bank that I loaded and unload both MEP-802A and MEP-803A units. The MEP-803A was sweetly loaded up to 67 amps.

Howdy, Not knowing what size the little mounting size is, wait until you physically have it, and look over the different aluminum project boxes for sale to mount them up into. That way it will be a nice finished end product. You can cut and dremel the mounting easily.

Howdy, Naming is everything... what are you calling the control box reset button's? Was a light lit on the Fault indicators? which one was lit? Have you run this MEP-802A before and loaded it to ensure its ready to go. Behind panel set for 120/240 single phase, hots to L1 and L3, N = neutral...