Search results

Howdy, Since you are thinking about it. I would suggest you go and inspect the units before you bid on them. You can look at everything. Pictures are good, but physically inspecting is always better.

Howdy, Do you have the connection to the lugs correct? MEP-802/803 single 120/240 connection below

Howdy, Military MEP-8xx TQG generators were overbuilt. (Plus, they are diesel) When they say 5kw, they mean 5kw 24/7 all day long without issue. When they say 10kw, the same thing applies, all day long. The only difference between the MEP-802A and MEP-803A is 2 cylinders. The engine is the exact...

Howdy, The bulkhead below the radiator is the same piece between 802 and 803. So you see where the 802 well nut goes with the hose. The fuel drain uses a well nut, but comes directly out the side. About 8 inches over from the oil drain.

Howdy, Some sites add stuff to get them up and running. Your sets looks like they went and got 4 batteries. One picture has the new positive battery cap sitting there.

Howdy, You have to take that with a grain of salt. The actual float can be positioned higher or lower. The best practice would to sit there and start the unit with a full tank. Start siphoning it out and watch when the aux fuel pump kicks on. Look at your gauge, Watch when the aux fuel pump...

Howdy, Don't fret about it. You purchased the unit. The best thing you can do is prep it good, and run it loaded to make sure you have cleaned out the pipes. That should be done whether it shows signs of wet stacking or not. That way you know when you need to use it, it will work when you need...

Howdy, It is really easy. Take the 1 bolt out, take the cover off. Take the roll pins out. Put you new stuff in. :) Grease it up, put it all back together.

Howdy, While it is not a 116 trailer, you can view the M1101/1102 trailers height here http://www.steelsoldiers.com/showthread.php?152816-M1101-M1102-LTT-TQG-any-newer-aluminum-trailer-height

Howdy, I will look if I have 1 more left. I sold a bunch way back then when I posted this.

Howdy, Yes, the 2 locations. I found that after having most of the coolant in, It was helpful to use the dead crank some. Hit the dead crank for a moment, fill some more, hit the dead crank some more, and fill. It seems that some does not want to go back behind the thermostat. This way the pump...

Howdy, 2 drain locations.

Tech Manual's are posted. AMMPS = Advanced Medium Mobile Power Sources (3rd generation) MEP-1030/1031 AMMPS 5KW 6115-01-561-7329 (3rd generation generator) TM 9-6115-749-10 TM 9-6115-749-24&P MEP-1040/1041 AMMPS 10KW 6115-01-561-7455 (3rd generation generator) TM 9-6115-750-10 TM...

MEP-1040/1041 AMMPS 10KW 6115-01-561-7455 (3rd generation generator) TM 9-6115-750-10 (operation) TM 9-6115-750-24&P (parts)

MEP-1070/1071 AMMPS 60KW 6115-01-561-7788 (3rd generation generator) TM 9-6115-753-10 TM 9-6115-753-24&P

MEP-1060/1061 AMMPS 30KW 6115-01-561-7718 (3rd generation generator) TM 9-6115-752-10 TM 9-6115-752-24&P

MEP-1050/1051 AMMPS 15KW 6115-01-561-7634 (3rd generation generator) TM 9-6115-751-10 TM 9-6115-751-24&P

MEP-1030/1031 AMMPS 5KW 6115-01-561-7329 (3rd generation generator) TM 9-6115-749-10 (operation) TM 9-6115-749-24&P (Parts)

Howdy, It sounds like the mechanic before you got into the fuel tank and moved your fuel sensor. That could be as simple as opening the front panel, loosen the locking hold down ring and lowering the fuel level sensor. Auxiliary fuel all relies on the fuel level sensor for turn on aux pump and...

Howdy, The unit might have had some wet-stacking when I picked it up. It is all cleaned off inside and outside. The unit starts and works great with any load up to 133%