Search results

Howdy, Well, if that is the case. You are then relying on the mep gauges to much. You need a meter connected to see if you really do have 120/240 and 60Hz. It sounds like the unit in question is not operating where it should. I must be a rocket scientist. :doh:

Howdy, Tm's needed TM 9-6115-751-10 TM 9-6115-751-24&P The starter for a MEP-1030 5kw, and MEP-1040 10kw is nsn 6110015958949 cage 44940 p/n 11.131.457 STARTER, MOTOR, 24 VOLT. They talk about using a lot of the same system to design the AMMPS units. The starter then again could be the same...

Howdy, Whatever your trying to accomplish, be careful. Standard US power is 60Hz, and 110-120 volts. A lot of larger appliances can make use of 208 volts when it specifies it does. Standard wave form on the lugs are 120 volts either side of the neutral. That is why the 2 hots give you 240. The...

Howdy, The M1101/1102 trailer are all aluminum. Magnetic lights are nice, but bring zip ties to old them on. Pintle hitch info and trailer ride height info here. M1101/M1102/LTT-TQG any newer aluminum trailer height OH, by the way, all rolling stock is on GovPlanet, not GL

Howdy, It sounds like you need to replace the Push-to-test lights.

Howdy, All the manuals you will need to do anything with your units are here on Steel Soldiers. All the manuals for the MEP-802, 5KW Generator and MEP-803 10KW Generator MEP-802A and MEP-803A manual information MEP-802A manuals you should have TM 9-2815-252-24_____ Diesel Engine...

Howdy, For a MEP-802/803 unit which has no power, lights, pump, start etc.... Make sure the Emergency Stop Button is pulled out. (also, maybe cycle it to make sure)

Howdy, Start at the top. Go thru start-up procedure. start your unit and put a load on it. *hint; pull out the emergency stop button. :roll:

Howdy, I have the whole little assembly for sale right here. http://www.steelsoldiers.com/showthread.php?153273-MEP-802-803-panel-components

Howdy, But, for all the extra goodies which will be backup supplies... all the panels and doors are the same, the fuel pumps, the fuel canister housing, engine, exhaust, all engine sensors, radiator, fuel tank, fuel level sensor (both), batteries, trays, cables, speed rpm cable, power...

Howdy, It's easier to say what is different. The alternator head. 60Hz vs 400Hz Your 2 meters on the panel. Hz setting and load a few voltage regulator parts in the control box. All the rest is usable. all other gauges, lights, switches, sensors, panels, engine etc...

Howdy Guy, You can get 30 of the little buggers for $5.00 - online. The Radio Shack's are drying up around here. Everything is toss and replace.

Howdy, Glad to have you on your way. :) You might have read a few threads already, but here are some pointers. MEP-8xx-series-Replacement-parts and since your in the control panel doing some wiring, you could add a few more wire jumpers to light up 3 other gauges...

Howdy, Are you talking about the knob for the fine tuning voltage ? if so, that is part MS91528-2K2B http://www.newark.com/ehc-electronic-hardware/ms91528-2k2b/round-pointer-skirted-knob-6-35mm/dp/98B9803 http://www.alliedelec.com/electronic-hardware-corporation-ehc-ms91528-2k2b/70206852/

Howdy, I can only say, that by seeing the screws holding in the S-1, it tells me it was swapped out.

Howdy, I have one unit which has the plastic blue S-1 switch. Your S-1 connections look a little off. That is why I suggest tracing out the wires for the S-1. Fuel lines? or fuel return lines? OH, by the way, Great first post with info which someone can help with. Has all the good info which...

Howdy, Sounds simple, but... Push in the big emergency stop button, and then pull it back out. update, after re-reading what you posted. It looks like the unit had the S-1 replaced. You might be better off undoing the wires and re-checking where they should go. Are the machine screws holding it...

Howdy, Good job. The Optima yellow tops are probably still good. They are AGM batteries. You use a special AGM charger and let them sit on the charger by themselves each for about 4 days. They will come back to life. Coolant, there are 2 locations which you need to drain. The simple one you...

Howdy, I use the load bank regularly. I can vary the loads easily. Anytime I start up a generator, I place a load on it. A load bank is just that. A method to put a electrical load on a generator. You can find all kinds of things used as load banks. Some members have used water heater probes...

Howdy, The unit started and ran. The sound was slightly muffled. I also had wet stack black goo around the exhaust manifold and muffler. That is just one of many reasons why I took it apart and physically cleaned the muffler, exhaust manifold and what I could reach on the head. I replaced all...