Search results

Kevin, I have the following, all new: 2-shocks, 26" long fully extended, w/clip #12460161-4 4-ball studs #12339609 2-bushings, rubber #12339602 2-decals #12340814 2-clamps for bushings #12341709 I sold my slant back and do not needs these. $100 takes it all plus ups. I cannot ship until next...

Kevin, There is a long and a short gas shock in each dampner. Which one did you wreck? I know I have new ones but I do not remember if they are the short or long ones. I have also have the outer tubes and mounting clips. To be sure, I will check tonight and post here. Hopefully I have what...

Are you talking about the pin in my picture? If so, I might have an extra...will check tonight and let you know. Regards,

Chuck, This is very well written and I thank you taking the time to pen it for us Michiganders!!! Best regards,

Sean Phylaw Eurotruck Importers http://www.eurotruck-importers.com/ http://www.eurotruck-importers.com/index.php?main_page=contact_us Check out his site and give him a call. Good honest person with a good business. Also, get the manuals! Attached is where my vin is.

RE: Day 2 Your hooker truck looks excited! Must be the snow that brings a chance for it to work!

Nice score Lane! you wanna sell it? I see that you are putting it work right away and making her earn her keep! What will the neighbors says with you out there at night with those lights? Also, drive her down here to get the tires so I can lift my mog plow out of the barn...it weighs 2000lbs...

Nice MOG! Perhaps I missed it in all the threads, but does the mechanical IP linkage actually actuate the IP? Make sure. The hand throttle should coincide with the fuel peddle thus verifying its position. My hand throttle is on the dash and rotates ccw to increase fuel. Mogs injection system...

Great pictures with details for my build! Any chance you have a few engine compartment pictures? Regards,

Hello, 8 bolt rim for bias and magnesium runflat 12 bolt rim for radial and rubber runflat I hope this helps. Regards,

Well I finally got to turn wrenches on the project last Saturday. Joel G showed up and we spent about 8 hours on it. I jerked the 10300 pound hubs and half shafts and replaced with 12100 pound ctis ready hubs and half shafts. I am not going to install the ctis system but I wanted the truck to...

Standard pioneer tools: shovel, axe and pick. It mounts under the rear frame for the standard hmmwv. Regards,

Hi Randy, I like the comments from others for I know a lot about some mv's and not a heck of a lot on others. So the more opinions, the better. The tub tag, according to others, is an early MB dating around the early 1942 time table. The price just set by my brother is $1000 with all parts...

Thanks pa.rich, seems one forgets the detail stuff at times when working and goofing off at the same time... Does not run, have not tried to turn engine over, does not have title. Price is to be determined by my brother when he gets back from travels. Regards, Added: Engine wants to turn...

Lane is correct on $$$. You can also try Yesterdays Tractors site ytmag.com for hauling. Good luck!

More info... Here are some more pics. The engine/transmission are not slat grille - here are the markings on the engine block, passenger side: 641087-W-13-D-PS CJ-CB. The head is marked JEEP in the center and FIRING ORDER 1342/TAPPET CLEARANCE ENGINE COLD/INTAKE 014 EXHAUST 014. The...

Lane, Argyle looks a heck of a lot warmer to operate! Specially when a pine tree decides to lose its load! BRRRRRR!

Thanks for the help and several g503 guys have ID'd this little bugger as a slat grill remnant. More pictures to be post soon. Regards,

RE: Aluminum Wheels - Super Singles - Bobbed Duece Last time I checked, my hmmwv tubs are aluminum and all have a ample amount of carc sprayed on them...Brushed aluminum rims might be anodized coated which could be an issue with carc.

RE: Not off topic.. Its a Yankee plow truck! Lane, It is good to know Argyle is being used and taken care of! Thanks for the pictures! For traction, I put some field stone on a pallet and placed in the rear, talk about traction! BTW, next time your down, I found the original SF97 form in my...