Search results

Poke around a little, you'll find several threads about using the bottle from a Suzuki Samurai ( 1987 vintage ) Available on the internet for like $15' You need to alter the hoses slightly, but it fits right into the bracket with 2 big zip ties.

Something else to keep in mind, clicking of the fuel pumps doesn't mean they are working properly. You have 2 pumps in line with each other and each pump has 2 check balls in it, one on the inlet and one on the outlet. If any of those 4 check balls gets stuck open or closed your fuel delivery...

Regarding your parts machine, the missing parts will be quite expensive to source individually. I have everything you need, but my suggestion would be to get the engine running first. If you could find a complete parts machine nearby for a reasonable price, that would be your most cost effective...

I'd start and the end of the line as well, and work backwards. Sounds like you have some contacts welded shut somewhere or shorted wires. disconnect the small signal wire from the silver starter solenoid to the right of the K1 relay, ( not the glow plug solenoid right next to it ) behind the...

The TM is located in the TM section at the top of the forum page. go through the menu and get yourself to the generator section, then find the mep-002 and 003 section. Get the 5-6115-585-34 Intermediate and Depot level maintenance manual, go to Pg. 136 and begin reading. You need to have the...

Definitely don't idle or operate under 56 Hz or so.... without disconnecting the excite wires, you WILL very likely damage the VR transistors if it's run at low RPM too long. Don't worry about operating without a load, the prior owner was probably thinking more about the older single cylinder...

The IP can seem intimidating the first time you do one. There are a couple simple tools I've made to make it a lot easier, but it is doable without these tools. If you read the TM, it explains how to properly set the engine in the right position ( cyl. #1 on the compression stroke with "PC"...

If you end up being unsuccessful, I'd suggest listing it for sale in the classified section. I'd guarantee there are SS members reading this that would be willing to purchase it for the right price and repair it. If you were a little closer I'd buy it in a heartbeat!

Humm.... couple thoughts. Often times the plunger guide will skip 90* rather than split in half and stop the plunger from turning. When the plunger guide skips it throws the fuel injection timing way off. This will usually still run but 3 bad things happen. 1) the engine will be very hard and...

Removing and rebuilding the IP is the only way I know of to free up stuck plungers. While you're in there upgrade to the 1 piece steel weight basket and coupler instead of the OE rubber coupler. They are available on Ebay for around $75 or maybe $125 for a rebuild kit with the steel coupler...

If I follow you correctly you are curious as to why you are seeing fuel in the return lines with the machine not running? If so, this is normal, the return lines and supply line to the IP are connected together. The base of the Tee fitting coming out of IP top cover should have a glass ball...

FYI, the solenoid doesn't retract until you crank the motor. Switching to Prim / Run doesn't engage the power to the solenoid.

Perhaps we should go back a little. What is your 003 doing, or not doing that makes you think the injectors are leaking into the cylinders? Does it run? if so, how well or how poorly is it running? Is it hard starting, or is the valve cover getting excessively hot fairly quickly? There are known...

The gasket is available direct from Cummins for $6Ea. https://shop.cummins.com/SC/product/onan-nozzle-insul-gasket-1470043/01t4N0000048kZ0QAI?srsltid=AfmBOortui0LYTdBcGdx6HgRkQbeAwJHQb5frSTjm6I6O39gHtuGpSVn

On page 160 of the -24P parts TM you can see the exploded diagram. The fiber washer is item #6 PN. 147-0043 , also comes as part of kits 147-0304 and kit 147-0307

The injectors seal to the head with a copper ring down against the head, a flat steel washer about 1/8" thick and a fiber washer above that which seals the injector body to the metal "washer" ( these 3 pieces are sold both individually and in a kit, PN's are shown in the TM ) However, the fiber...

Go ahead, ask away! ;-)

I'd be interested in hearing more about your WMO project when you get it going. My son recently tried making black diesel to run in some of my equipment as well as our 002 and 003 and the steam genny too. It worked ok, but he was kind of guessing at the proportions which were off a little...

FYI, there is a minimum number of post required on your account before you can send a PM without the help of a moderator. Since you're new you're not able to send PM's directly on our own yet.... all in due time!

For the frequency transducer you can either remove it and use a direct line read frequency meter, or there were TRC frequency transducers selling on ebay for <$20 that will work and just need a couple new mounting holes drilled in the control cube. There are definitely other posts here where...