Search results

Click on my name in the very upper left of my post. Then click Private Message. Compose your message. Click Submit Message.

The 802 one got "smoked" because you applied 24 volts directly across it's terminals. The 802 one needs a current limiting resistor with it. Without it you killed the 802 indicator LED. PM me your email address and I'll send you a version of the TM that has very clear schematics in it. You...

With the set running you should see ~ 28 volts DC across the Hour Meter terminals. Terminal 1 should have ~24-28 volts DC on it when S1 is in the RUN position. Terminal 2 should have 0 volts DC on it with the contactor closed. Terminal 2 should have ~28 volts DC on it with S1 in RUN and the...

The reading at A to B represents the actual RPM.

Hmmm... Something still isn't right with the adjustments. The rod should never be able to lift itself out of the hole. The rod ball should always be in contact with the black lever when it's running or stopped. Never a gap between them when running or stopped. The ball lifting off the arm...

Yes I had bare printed circuit boards built a while back, built up a few units sent unit out for beta test. Once beta testing was completed I had to re-spin the bare PCB design and received the new versions yesterday. Started populating the first one with components last night. Waiting on...

Didn't know you were missing part of the housing. Looks like you'd need to order a complete housing assembly to get the lens that holds the bulb. Not cheap from DigiKey..$42 https://www.digikey.com/products/en?keywords=800-1030-0337-504 Also on ebay. Search for 800-1030-0337-504

Ahhh... You're looking at the 2010 TM, I was looking at the 2005 TM. You are correct they call out a LED lamp in the 2010 version. The PN 98-19763 cross references to a Dialight PN 586-1102-005F. That bulbs spec are: T1 3/4 base, 28 V, Green, 520 nm Wavelength, 600 mcd brightness Looks like...

The fan doesn't have wires. It has two metal tabs the fan power cord slips onto. I'm looking for a replacement lamp for you...

The fan is a Rotron part number 031842. They are on ebay for $25. Also available on DigiKey and Allied Electric. The Contactor lamp is an incandescent bulb, not an LED. ** edit, it can be an LED or Incandescent

Here is a pic of one of them.

You won't find that adjustment in the TM. It's factory set and is secured in place with a safety wire and lead seal at the factory. So for a starting point for that adjustment I took measurements of that adjuster on my two 831's. The adjusters height from the plate to the top of the bolts were...

Those likely are lot codes or date codes on the device which will vary.

The IRFP450 is spec'd at 500V and 14A. Looks like you probably ordered the right one. What make and part number did you order? To get the exact specs you'd need to determine what manufacturer made it. The specs vary slightly from manufacturer to manufacturer. Usually there is a...

https://www.steelsoldiers.com/showthread.php?154446-All-the-TM-s-you-need-to-work-on-the-MEP-005A

See section 5.3 in --> https://www.steelsoldiers.com/showthread.php?122965-FIELD-AND-SUSTAINMENT-and-MAINTENANCE-2k-THRU-200k-TQG-GENERATOR-SETS Some info about it..

Congrats! The pictures aren't the best resolution so it's a bit hard to make things out. I looks like that one of the mechanical governor adjustment bolts may be missing.

Remote Start Controller Kits For use in MEP-802A, MEP803A, MEP-804A, MEP-804B, MEP805A & MEP-806A Generators WiFi Remote Control & 2-Wire Start/Stop Features include: · Remote genset Start/Stop via WIFI via cell phone, laptop, tablet · Direct WiFi communication. No router needed...

Replacement Governor Controller Modules for the SLC100 Part Numbers 2990-01-477-1371, 98-19539 Used in MEP-831A & MEP-832A Generators $220 Includes USPS Priority Shipping in the US and to US Territories & Guam Shipping outside the US will be actual shipping cost PayPal & Checks accepted...

I have a version of my 802/803 WiFi Remote Start and monitor system for the 831 already which includes the variable Governor Controller electronics for the the 831 with the Inverter. Just need to re-spin the PCB into the final version and build some units. I'd need to evaluate if it's cost...