cucvrus
Well-known member
- 11,473
- 10,434
- 113
- Location
- Jonestown Pennsylvania
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
CUCVRUS Repair Projects
- Thread starter cucvrus
- Start date
cucvrus
Well-known member
- 11,473
- 10,434
- 113
- Location
- Jonestown Pennsylvania
I am using the 1987 M1028 CUCV as a daily driver whilst my Silverado is in getting oil cooler lines changed. One would think by now that they can make oil cooler lines that will not leak. I made my own on a few CUCV's. Have a Great Day. Be Safe.
I'm surprised that they have the parts in stock for that!! Imagine how many they need just by looking at that recall number. Must be a fun job too at that much hour billed vs 2wd and 4wd! I'll pass on that warranty work! Have fun with the new old daily driver.
cucvrus
Well-known member
- 11,473
- 10,434
- 113
- Location
- Jonestown Pennsylvania
They offered me a loaner car and I said no I will drive the CUCV. If it was spring/summer, I would drive the loaner. The lines are on national back order, and I still like my new trucks more than the old ones. Comfort and a place to set my coffee cup. have a Great Day. And no, I don't need any add ons to the CUCV. It has worked great going on 40 years.
cucvrus
Well-known member
- 11,473
- 10,434
- 113
- Location
- Jonestown Pennsylvania
I had an M1009 snowplow truck dropped off at my barn. Owner said it won't start and he tried changing the filter and can't get it primed. I hopped inside and turned the key on. Fuel gauge over at 3 o'clock. I said
25 gallons later and it was off and running. He said it also has no brakes. I looked at the master cylinder and both reservoirs were empty. I put a small amount of DOT 5 in each reservoir and pumped the brakes. The right rear is leaking at the backside of the backing plate and has been for years. It looks like it has fur growing on it and I didn't find any leak up front except the outside of the master cylinder is leaking. I think the front brakes were compensating for no rear brakes and he was stabbing the brakes and the fluid was jetting against the lid and slowly leaking out the lid seal. That is my thoughts. Anyway 1 problem is fixed. And he mentioned fixing the fuel gauge. I am not sure I want to get involved in that time alone it looks like a nightmare. The transmission lines are spliced together with hose at different places. Most times I get the work after a butcher has worked on it and the butcher didn't want to work on it anymore. More FUN in the February sun. Take Care and Be Safe. I see $$$$ and know the owner don't understand. I will give an estimate.
Last edited:
I think once he gets the 300$ bill to fill up the tank you'll know if he's up the other repairs!!
cucvrus
Well-known member
- 11,473
- 10,434
- 113
- Location
- Jonestown Pennsylvania
cucvrus
Well-known member
- 11,473
- 10,434
- 113
- Location
- Jonestown Pennsylvania
LT67
Well-known member
- 655
- 501
- 93
- Location
- Bowdon, GA
When I bought my 86 M1008, it had a Vintage Air full electronic AC system in non working condition. Long story short I got it fixed last year and now I'm spoiled lol
cucvrus
Well-known member
- 11,473
- 10,434
- 113
- Location
- Jonestown Pennsylvania
Real CUCV's don't have A/C in the driver's cab. Never needed it. M1010 had it and you could A/C the cab with the access door open. Have FUN. I still like the bone stock CUCV's best.
LT67
Well-known member
- 655
- 501
- 93
- Location
- Bowdon, GA
AC comes in handy when I drive it for work... and our summers in Ga can emulate a sauna
cucvrus
Well-known member
- 11,473
- 10,434
- 113
- Location
- Jonestown Pennsylvania
I finally fixed that 30-amp fuse for the lighting. It was a cheap fix. Stays tight and does not melt the plastic.ezgn
Well-known member
- 650
- 1,039
- 93
- Location
- Lake Elsinore Ca.
You almost had me on that one, ha ha I think the 20 amp fuse next to it exposed your trickery. I was just thinking about you today. I hope you and you're family are doing well.
Elektroman99
Active member
- 169
- 138
- 43
- Location
- Siegburg, Germany
Questions about a Chevrolet Blazer K5 / M1009, first registration 1986
So, the speedometer and fuel gauge remain "Dark".
It is only about the "backlight".
I checked the "dim" function, but it was not the cause of the missing background light.
Here is a picture of the fuses:
www.dropbox.com
So, the speedometer and fuel gauge remain "Dark".
It is only about the "backlight".
I checked the "dim" function, but it was not the cause of the missing background light.
Here is a picture of the fuses:
Dropbox
www.dropbox.com
There are several small bulbs (194/16
on the back of the gauge cluster. When all are lit, you can see all parts, fuel, speedometer, etc. The ammeter has it's own bulb, so does the heater control panel. I replaced all of mine with Blue LED's and it looked great.
on the back of the gauge cluster. When all are lit, you can see all parts, fuel, speedometer, etc. The ammeter has it's own bulb, so does the heater control panel. I replaced all of mine with Blue LED's and it looked great.
cucvrus
Well-known member
- 11,473
- 10,434
- 113
- Location
- Jonestown Pennsylvania
In God We Trust was the winning combination for this fix. Honest Abe doing what no fuse can do. Keeping the power flowing.
cucvrus
Well-known member
- 11,473
- 10,434
- 113
- Location
- Jonestown Pennsylvania
These are bigger cabs than the CUCV K30 but still a cool picture. Happy Easter.
- 653
- 533
- 93
- Location
- Reydon, OK
Medium duty truck cabs??
cucvrus
Well-known member
- 11,473
- 10,434
- 113
- Location
- Jonestown Pennsylvania
Happy Easter to all. Hope to see you in church. Take Care.
cucvrus
Well-known member
- 11,473
- 10,434
- 113
- Location
- Jonestown Pennsylvania
I have been venturing back out to my barn. I am making slow progress getting things cleaned up and cleared out of the way so I can work on tractors and lawn equipment. I want to get my M1009 project completed for its 40th anniversary. The set back in December is still fresh on my mind. Take Care. Be Safe and Have Fun.