212sparky
Well-known member
- 1,822
- 38
- 48
- Location
- Monroe/ Ohio
Oh we got picturesThat can't be true or you would have posted pictures, or even videos.
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
What did you do to your deuce this week?
- Thread starter Seth_O
- Start date
- 18,550
- 5,913
- 113
Looks good for parades and patriotism....
... however:
Your outward canting of the staffs places your vehicle's overall width OVER 8 ft. and may be a problem in some jurisdictions. You may have just crossed that OVERSIZE VEHICLE line.
8-1/2 feet is legal on interstate highways and on many State's highways as well, but NOT ALL. Some cities also limit OVW (overall vehicle width) to just 8'.
Typically, Mirrors are allowed to exceed the width limits IF THEY ARE OF A BREAK-AWAY DESIGN.
Are your flag staff mounts a "break away" design?
Last edited:
SteveKuhn
New member
- 1,227
- 4
- 0
- Location
- Hasbrouck Heights NJ
My mirrors might be a breakaway design but the rust took care of that.
Steve
Steve
rwminck
New member
- 71
- 0
- 0
- Location
- Florence SC.
ColdWarrior, They are definetly not brake-away, I used 1/4" steel and thick wall 316SS pipe. I did not really think of being oversized, but it looks much worse than the picture shows. I will have to go measure. Thanks for the prospective, I would not of thought about it. Thanks
brianp454
Member
- 572
- 11
- 18
- Location
- Portland, OR
That is a good lookin' truck!
Cool, can't wait to live vicariously through them when you post them.Oh we got pictures
ralph3162
New member
- 164
- 2
- 0
- Location
- Pleasanton / Texas
Well I did manage to get the winch in the back bolted in today. So now I can load those big heavy 11.00 x 20 spare tires in the back by myself now. It got dark so the wiring and controls will have to wait until tomorrow. 
I also got the base today so I was able to finish installing the new passenger seat. 
I also got the base today so I was able to finish installing the new passenger seat. 
- 37
- 0
- 6
- Location
- Grove City Pa.
I was able to get it painted and put back together this week. 
Jeepsinker
Well-known member
- 5,399
- 457
- 83
- Location
- Dry Creek, Louisiana
I started painting mine as well today during the whole two hours I had when it wasn't raining. Hoping for no rain tomorrow.
- 18,550
- 5,913
- 113
I sure didn't want to be a party-pooper. You've done some good work. Just figured it's better to consider those thoughts than to get a hefty citation for not fitting in your right-of-way.
Carry on.
Crush36
New member
- 38
- 0
- 0
- Location
- Atlanta, Ga
Sprayed the front side fenders and front bumper with spray on bed liner.
Crush36
New member
- 38
- 0
- 0
- Location
- Atlanta, Ga
Also sprayed the side steps and rear bumper with spray on bed liner.
srodocker
Well-known member
- 6,549
- 69
- 48
- Location
- Lacey, Washington
More info on the spray you used?
Crush36
New member
- 38
- 0
- 0
- Location
- Atlanta, Ga
Took it out for a 90 mile test drive after all the work I have done to it over the past 4 months.
Crush36
New member
- 38
- 0
- 0
- Location
- Atlanta, Ga
The material I used I order off of e bay. Called liner X-treeme, I have tried several different brands and this is the best stuff I have found and at a reasonable cost. The kit makes about 3 gallons of spray able material. Comes with 2 gallons of base, 2 quarts or reducer, 2 quarts of activator, and 2 bags of ground up rubber which is pretty fine, I would say there is about 4 cups of rubber per bag. It also comes with the spray gun. I sprayed it at about 75 PSI. The cost of the kit was $165.00 and $40 for shipping. The kit comes so you can mix 1 1/2 gallons at a time. It also comes in several different colors. It took 2 kits to do inside the entire bed... It took 1 kit to do the front fenders, front bumper, side steps, and rear bumper. It took 1 kit to the the entire interior and I also did the supports for the troop seats which I did in desert tan. Hope this was helpful.
Pugsley
Member
- 92
- 4
- 8
- Location
- NW Indiana
I drove mine all over Haspin!
gunboy1656
Active member
- 3,587
- 22
- 38
- Location
- Beaver Falls, PA
I proved a deuce is not a very big truck.
Attachments
Carlo
New member
- 1,364
- 20
- 0
- Location
- palazzago italia
I've always liked these, BIG!
Jeepsinker
Well-known member
- 5,399
- 457
- 83
- Location
- Dry Creek, Louisiana
Just finished painting mine. It has been an epic battle.
welldigger
Active member
- 2,602
- 16
- 38
- Location
- Benton LA
No pics?