msgjd
Well-known member
- 1,079
- 3,311
- 113
- Location
- upstate ny
ha ! At first I was gonna make a play off the "doctor" thing , until I saw your updated comment.
So you are a DVM these days?
You know... Deuce Vehicle Mechanic... ?
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
What did you do to your deuce this week?
- Thread starter Seth_O
- Start date
- 444
- 836
- 93
- Location
- Orygun
Saw no reason for the stock configuration to leak, yet they did, not anymore
Edit: in hindsight I do not at all care for the shiny aluminum parts on my engine, wish I had painted it first and I shall still, with a little brush, maybe filters too with a spray can
Edit: in hindsight I do not at all care for the shiny aluminum parts on my engine, wish I had painted it first and I shall still, with a little brush, maybe filters too with a spray can
Last edited:
- 2,053
- 2,949
- 113
- Location
- Florence, SC
Nice, that's on my future to do list for my 64 model!
Oil filters are not too much a problem for me so far, however the fuel filters are another story. Definitely will look into a spin on set up for at least the two twin secondary filters.Saw no reason for the stock configuration to leak, yet they did, not anymore
Edit: in hindsight I do not at all care for the shiny aluminum parts on my engine, wish I had painted it first and I shall still, with a little brush, maybe filters too with a spray can
biscuitwhistler37
Well-known member
- 292
- 858
- 93
- Location
- Michigan
Finished starting her bunkhouse the other night, gonna dive into tags and numbers and see what history I can find before deciding what maintenance to perform next. Til next time!
- 124
- 213
- 43
- Location
- Florida
Finally finished a large serving on Deuce 2 to include:
6 new inner hub seals
4 new outer axle seals
2 new front axle tube seals
6 new axle lock washers
6 new brake cylinders and associated banjo bolts, washers, etc.
All new rubber brake lines
4 new hard lines on front and center axle
Power bled brakes twice with DOT 5 silicone fluid
New heavy duty tie rod from Boyce Equipment CO.
2 NOS tie rod ends
4 New king pin bushings and shims
2 new black silicone axle boots
4 new boot clamps
2 new inner wheel bearings on front axle
2 new outer wheel bearings on front axle
24 new spindle studs with new washers and nuts
Used a thread chase on all 36 wheel studs
CONSUMABLES
Over 100 cans of brake cleaner
9 rolls of blue shop towels
1 can of Cyclo Break Away
All said and done, it was tons of fun!
6 new inner hub seals
4 new outer axle seals
2 new front axle tube seals
6 new axle lock washers
6 new brake cylinders and associated banjo bolts, washers, etc.
All new rubber brake lines
4 new hard lines on front and center axle
Power bled brakes twice with DOT 5 silicone fluid
New heavy duty tie rod from Boyce Equipment CO.
2 NOS tie rod ends
4 New king pin bushings and shims
2 new black silicone axle boots
4 new boot clamps
2 new inner wheel bearings on front axle
2 new outer wheel bearings on front axle
24 new spindle studs with new washers and nuts
Used a thread chase on all 36 wheel studs
CONSUMABLES
Over 100 cans of brake cleaner
9 rolls of blue shop towels
1 can of Cyclo Break Away
All said and done, it was tons of fun!
biscuitwhistler37
Well-known member
- 292
- 858
- 93
- Location
- Michigan
So buy brake cleaner by the barrel. Noted
On second note, I hear the stock ones do not have the backflow valve like spin ons.Saw no reason for the stock configuration to leak, yet they did, not anymore
Edit: in hindsight I do not at all care for the shiny aluminum parts on my engine, wish I had painted it first and I shall still, with a little brush, maybe filters too with a spray can
View attachment 913184
Where do you get a kit.like this?
- 444
- 836
- 93
- Location
- Orygun
tie6044 has them, so does jatonka, they are both on here just shoot em a message .
I have bought from both .
Tie6044 also sells his on Fleabay under same name
- 124
- 213
- 43
- Location
- Florida
More work on Deuce 2…
Replaced 6 fuel injectors, new copper washers and new rubber injector seals
Replaced fuel Injector return line to include all new fittings
Replaced primary fuel filter
Replaced fuel tank to primary filter head hose
Replaced hose from primary fuel filter head to injection pump
Replaced fuel hose to flame heater and replaced flame heater filter
Replaced 6 fuel injectors, new copper washers and new rubber injector seals
Replaced fuel Injector return line to include all new fittings
Replaced primary fuel filter
Replaced fuel tank to primary filter head hose
Replaced hose from primary fuel filter head to injection pump
Replaced fuel hose to flame heater and replaced flame heater filter
- 5,367
- 3,378
- 113
- Location
- Lexington, South Carolina
I doubt you will ever need the flame heater while in Florida. It's primary use was to heat up the incoming air enough to get the LD series engines to start when the temp was at 0 degrees F or lower. All new lines will help, but it remains a point of failure that most of us in the south can avoid.
- 124
- 213
- 43
- Location
- Florida
We have property in the Pacific Northwest and I will be taking Deuce 2 out there so want to be able to start in the negative temp range. Deuce 1 has its flame heater deleted as it will live in Florida,
speaking of flame heater, I was sold this replacement spark plug with a different part number than the Autolite currently in the truck. The old PN is 1093558 the new PN is a Champion 733556; are they compatible? The new one has an offset tip from the center electrode. The NSN of the new plug is 2920-00-411-5747.
Attachments
Another Ahab
Well-known member
- 17,999
- 4,556
- 113
- Location
- Alexandria, VA
Morse Code is still alive-and-well?!
In a world of runaway tech, that is reassuring in a way.
banditt1979
Well-known member
- 273
- 738
- 93
- Location
- Cincinnati, OH
Today I finally changed the gear oil in the transmission and transfer case. Trans oil was slightly dark but not bad. Transfer case oil looked and smelled like new. Some bronze shavings in the oil but no chunks. Penn Grade 80w90 gl4 good stuff safe for yellow metal.
Another Ahab
Well-known member
- 17,999
- 4,556
- 113
- Location
- Alexandria, VA
You got yourself a right nice looking garage there, BGR. Sweet!
I wish, it's my buddy's auto shop, Magnolia Auto Service. He does a lot of good work for me.
banditt1979
Well-known member
- 273
- 738
- 93
- Location
- Cincinnati, OH
I mounted two of my new ndt tires on the front and broke down one more wheel. Replaced a return spring that had broken on the throttle return.
Hello my friends! It's Dipstick. I hope some of you remember me. I sold Brutus several months ago. As I am rapidly approaching 71 years of age, I felt I was no longer able to maintain Brutus the right way. That along with rust and my constantly dwindling financial status also took they're toll. I now drive a 2012 Jeep JK, which is remarkably similar to driving a Deuce! It feels like I'm driving a mini-Deuce. I love it. I hope everyone is doing well!!!