…did you find that white wire???Wiring.
- YouTube
Enjoy the videos and music you love, upload original content, and share it all with friends, family, and the world on YouTube.youtube.com
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
What have you done to your FMTV or LMTV today
- Thread starter Coffey1
- Start date
AllenF
Member
- 56
- 38
- 18
- Location
- Riverside, Ca
On those silicone blades from piaa. I bought a set for my 2005 F-350 in 2006. They still work very well and are silent. No chattering. Yep that is 16 years so far. single best thing I have EVER done to a vehicle. Talk about bang for buck!
- 705
- 1,805
- 93
- Location
- San Diego, CA
I've been designing and building over the windshield shelf pockets on both sides that will have a double DIN stereo in between. Each side has two openings and one opening is big enough and deep enough for a 15-16 inch laptop. They are lighted with red LED neon rope lights.
- 705
- 1,805
- 93
- Location
- San Diego, CA
Where's waldo
ramdough
Well-known member
- 1,554
- 1,729
- 113
- Location
- Austin, Texas
- 705
- 1,805
- 93
- Location
- San Diego, CA
Install finished. I'll do the center radio area in the future when I actually have a radio to put in it!
- 494
- 1,073
- 93
Spent some time dressing up my door panels and adding a bunch of sound deadening. Turned out pretty good for what it is.
New window cranks... and. Broke both new plastic door handle covers trying to get them on... what a dumb design. I think I might order some handles that match my window cranks. The windows cranks were a bit cheap, and the knobs squeaked and rattled, so I threw in a small ring to take up the slack, and hit it with a bit of lube.... 100 times better.
Fabric was just some outdoor chair replacement fabric I picked up a JoAnn Fabrics by the yard and I just glued it to the old door panel and flush trimmed it with a razor blade.
Then I punched the holes for the plastic push in fasteners and dropped in some 1/4-20 nutserts and used some stainless machine screws with trim washers to hold the panels on.
I put some asphalt sheet sound deadener in the drro attached to the inside of the drro skin, and I covered the entire back of the door panel with the same stick on sheets.
I also taped all of the openings in the door over with gorilla tape to keep any air intrusion to a minimum.
While I was doing all of this, my lovely wife put asphalt sound deadener into all of the ceiling recesses.
New window cranks... and. Broke both new plastic door handle covers trying to get them on... what a dumb design. I think I might order some handles that match my window cranks. The windows cranks were a bit cheap, and the knobs squeaked and rattled, so I threw in a small ring to take up the slack, and hit it with a bit of lube.... 100 times better.
Fabric was just some outdoor chair replacement fabric I picked up a JoAnn Fabrics by the yard and I just glued it to the old door panel and flush trimmed it with a razor blade.
Then I punched the holes for the plastic push in fasteners and dropped in some 1/4-20 nutserts and used some stainless machine screws with trim washers to hold the panels on.
I put some asphalt sheet sound deadener in the drro attached to the inside of the drro skin, and I covered the entire back of the door panel with the same stick on sheets.
I also taped all of the openings in the door over with gorilla tape to keep any air intrusion to a minimum.
While I was doing all of this, my lovely wife put asphalt sound deadener into all of the ceiling recesses.
- 705
- 1,805
- 93
- Location
- San Diego, CA
I bought new window cranks that look a little nicer and are a little longer and used my old window cranks as my new door latch handles
ramdough
Well-known member
- 1,554
- 1,729
- 113
- Location
- Austin, Texas
Do you mind posting the link for those cranks? I need all new cranks too.
Sent from my iPhone using Tapatalk
- 494
- 1,073
- 93
Keep in mind that they re not super high quality...
These are the ones I have now.
https://www.amazon.com/gp/product/B07GFLFGHW/
but they are a brushed/mattte finish, and I was unable to find the door handle in that same finish, so I'll be ordering these:
https://www.amazon.com/gp/product/B07R3X4X4G/
And these:
https://www.amazon.com/gp/product/B07R4SDW55/
And if they turn out to be total crap. Lokar makes some that come at a premium cost, that are likely to be better quality, although I have not verified they will fit on the shaft yet. The details on the shaft size are a little lacking for the Lokar units. I'll probably have to contact them to get the details.
https://www.amazon.com/Lokar-IDH-2009-Polished-Billet-Aluminum/dp/B004U3WXS0
https://www.amazon.com/Lokar-IDH-2015-Polished-Billet-Aluminum/dp/B004U3WZ3S/
Wingnut13
Well-known member
- 235
- 563
- 93
- Location
- Strafford, NH
^^ Didn’t do anything that cool^^
I just made a door handle latch. Mine was coming apart, the pot metal it’s cast of is complete garbage. So I used 1/8” steel and made a new handle and legs. Totally not worth the time, unless you aren’t able to order new/different handles.
I just made a door handle latch. Mine was coming apart, the pot metal it’s cast of is complete garbage. So I used 1/8” steel and made a new handle and legs. Totally not worth the time, unless you aren’t able to order new/different handles.
- 705
- 1,805
- 93
- Location
- San Diego, CA
You can buy another pack of those window cranks and remove the knob and use them for your door release so they match
Attachments
- 882
- 525
- 93
- Location
- tucson AZ
Removed the cab. I've seen the use of a big crane to do this, but the cab only needs to be lifted a couple of inches then can be moved straight forward and off. With the "floating" crossmember still attached the cab sits flat on a pallet. Some lag bolts secur it there.
- 494
- 1,073
- 93
Goofing off while waiting for parts to arrive....
Messed about with nickel plating my door pulls. The old paint was worn, and the current durability of paint and powder coatings just aggravates me. So I gave them a run through the sandblaster and then a 30 minute swirl in my homemade plating setup.
In retrospective finish turned out rougher than I would like. More prep time would have been better.
Messed about with nickel plating my door pulls. The old paint was worn, and the current durability of paint and powder coatings just aggravates me. So I gave them a run through the sandblaster and then a 30 minute swirl in my homemade plating setup.
In retrospective finish turned out rougher than I would like. More prep time would have been better.
- 7,771
- 19,879
- 113
- Location
- Charlotte NC
.
Wonder if you could polish it up a bit with something like jewelers rouge?
- 673
- 894
- 93
- Location
- SW Va, Roanoke County
Love the look of your door panels
- 705
- 1,805
- 93
- Location
- San Diego, CA
What's the capacity of that hoist?
- 494
- 1,073
- 93
Thanks. They turned out really well, and it was super easy. If you are so inclined, I'd encourage you to give it a go.
It was pretty affordable too. I bought 2 yards of the sun chair fabric, because I wanted something that was not fuzzy so as to not collect dust/dirt/mud. They did not have a huge selection, but they did have several choices of colors and materials that were suitable. I picked this pattern because it reminded me of the old International Scouts with the bold, plaid interior finishes.
My wife used a 50% off coupon and I got the fabric for less than $30, and I think I have enough left over to do it again in case a I manage to damage one.
I do have some concern about the edge peeling off and considered adding some edge trim to cover it, but so far it's not an issue since the panel sits in a small recess in the door framing.