• Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!

  • Microsoft MSN, Live, Hotmail, Outlook email users may not be receiving emails. We are working to resolve this issue. Please add support@steelsoldiers.com to your trusted contacts.

What have you done to your HMMWV today/lately

Mainsail

Mainsail

Well-known member
Steel Soldiers Supporter
1,512
1,696
113
Location
Puget Sound, WA
Coug said:
You doing the Auburn parade?
I have other commitments tomorrow or I would do it.

If you aren't doing anything else Monday, come on down to the Elma Veteran's Day Parade and join that one as well. Even if it's pouring rain we tend to enjoy ourselves (VFW parade entry) More trucks are always welcome.
Click to expand...
Poulsbo has a little parade for Veteran's Day. Last year I carried the WWII vets who were the Grand Marshalls as the lead vehicle (behind PFB's giant ladder truck). This year I was scheduled to do the same but they told me a few days ago the vets are getting to an age now where ingress and egress to the M1165 isn't going to be practical, so they'll be loaded into something else. I'll be back at #19 in the formation and not sure who I'm carrying.

If thing even goes off I'll be surprised - seems very disorganized this year. It's only their second annual so I guess I got in on the ground floor last year.

Parade02.jpg
 
Last edited:
J

JC34

New member
2
0
1
Location
WV
C

Coug

Well-known member
Steel Soldiers Supporter
3,003
4,420
113
Location
Olympia/WA
Finally got around to replacing the dead marker light in the rear. Had the power wire broken off at the light, so no way to fix.
Other three lights worked, but were a little dim. I thought it was just the lenses.
Nope. As soon as I installed the new marker light, the other three went dead. Fixing the grounds for better connection didn't change anything.
So today replaced the other three marker light assemblies. All are functioning properly now.

Next thing is to assemble some relays to turn the front two marker lights into turn signals. Should be pretty simple to use a NC relay with the coil side wired to the front turn signals to interrupt power to the markers whenever the turn signal is on.
Will try with some cheap 24v relays first, and if I like it well enough if/when they decide to fail I'll either find some solid state relays that can be waterproofed or cough up the money for the ones from camotek.
 
Caactus

Caactus

Active member
83
202
33
Location
NW Phoenix, Arizona
Coug said:
….
Next thing is to assemble some relays to turn the front two marker lights into turn signals. Should be pretty simple to use a NC relay with the coil side wired to the front turn signals to interrupt power to the markers whenever the turn signal is on.
Will try with some cheap 24v relays first, and if I like it well enough if/when they decide to fail I'll either find some solid state relays that can be waterproofed or cough up the money for the ones from camotek.
Click to expand...
My front left marker has gone dead and a fix is on my list. Was wondering if your plan was possible.. so I’ll be following this..
 
C

Coug

Well-known member
Steel Soldiers Supporter
3,003
4,420
113
Location
Olympia/WA
Honestly it took about 10 minutes to replace.
Caactus said:
My front left marker has gone dead and a fix is on my list. Was wondering if your plan was possible.. so I’ll be following this..
Click to expand...
Only real issue is 2 of the machine screws on each marker were corroded to the point I had to drill the head off to remove. Screw is #10 x 24 7/8" long and used a nylock nut on the inside. The rear are 5/8" long. Parts manual gave different thread pitch between front and rear, and regular nuts instead of nylocks for the rear, but should be easy to go to the local hardware store and buy hardware that matches front and rear with rear being 3/4" and front being 1" long unless you want to special order them.
I also used NO OX ID grease on all of the mounting screws, with a bit extra on the ground one (just grease with electrically conductive additives) You could also use dielectric grease instead as it will keep the air out and the surfaces should be tight enough to make a good connection anyway.
 
TOBASH

TOBASH

Father, Surgeon, Cantankerous Grouch
Steel Soldiers Supporter
Supporting Vendor
3,596
3,518
113
Location
Brooklyn, NY
Coug said:
Finally got around to replacing the dead marker light in the rear. Had the power wire broken off at the light, so no way to fix.
Other three lights worked, but were a little dim. I thought it was just the lenses.
Nope. As soon as I installed the new marker light, the other three went dead. Fixing the grounds for better connection didn't change anything.
So today replaced the other three marker light assemblies. All are functioning properly now.

Next thing is to assemble some relays to turn the front two marker lights into turn signals. Should be pretty simple to use a NC relay with the coil side wired to the front turn signals to interrupt power to the markers whenever the turn signal is on.
Will try with some cheap 24v relays first, and if I like it well enough if/when they decide to fail I'll either find some solid state relays that can be waterproofed or cough up the money for the ones from camotek.
Click to expand...
The trick with LED marker lights is to get a constant ON relay. Then it will flash OFF when activated. That avoids issues that can occur with certain bulbs IIRC.
 
C

Coug

Well-known member
Steel Soldiers Supporter
3,003
4,420
113
Location
Olympia/WA
TOBASH said:
The trick with LED marker lights is to get a constant ON relay. Then it will flash OFF when activated. That avoids issues that can occur with certain bulbs IIRC.
Click to expand...
Yeah.
The relays I ordered are single pole double throw, and have both the normally closed side and a normally open side. Wiring through the normally closed side should give power until the turn signal is energized.

I plan to just tap into the turn signal and T off of it to make a parallel circuit , so relay gets a separate ground, rather than in series with the turn signal because I expect that would cause issues.
My front turn signals are pretty much the only thing left in my truck that aren't LED, because of the flasher issue.
 
You must log in or register to reply here.
111,192members
165,489threads
2,328,842posts
1,625online users
Top
✖
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website like our supporting vendors. Their ads help keep Steel Soldiers going. Please consider disabling your ad blockers for the site. Thanks!

I've Disabled AdBlock
No Thanks