Search results

If you get that thing to run and you get those 24V GPs to work, please let me know. I have a ass ton of 24V plugs and I don't wanna spend $90 on AC 60Gs. Mike :beer:

I have two questions. First, I have a bad GPC Relay and I happen to have three or four spare, relays that are the same as the GP Relay except they are 24 volts in and out. I also have 2 sets of 24V glow plugs. Can anyone tell me if I can do a manual glow plug set up WITH a 24V relay? Also, I...

Thanks for the advice Flyboi. I am running AC Delco 60s which everyone says are the best. Once the injector nozzles get in, I'll change out the plugs again and check the temp. Eventually, I know Im gonna have to rebuild this engine. Maybe this summer.

Same here. What is this Aircraft Spruce you speak of? Is it a website?

Changed sway bar bushings, king pin springs, tie rod ends and ball joints. Then glow plugs and fuel filter. Then I snapped the **** bleeder screw. Conveniently, none of the parts stores carry that screw. Any suggestions?

im not for sure how big they are and The computer I have them on does not have CD burning capabilities. I have no idea if they are available to the public or not, I just know that they are **** near obsolete. It seems retarded to me that they would not allow a TM to be used by the public. Are...

All it says is this: THIS PUBLICATION IS REQUIRED FOR OFFICIAL USE OR FOR ADMINISTRATIVE OR OPERATIONAL PURPOSES. DISTRIBUTION IS LIMITED TO U S GOVERNMENT AGENCIES ONLY. OTHER REQUESTS FOR THIS DOCUMENT MUST BE REFERRED TO COMMANDANT OF THE MARINE CORPS (ARD), WASHINGTON, D C 20380-0001

Sorry about that, didn't realize I was in the CUC section. I dont know if they are approved for public use or not. How can I find out?

Ive been getting my ass kicked by my relay as well. I thinkn my problem is actually with the Module though and as I have yet to find a replacement for the module, I am looking around on how to bypass that completely. If you opt to get a new relay, Advanced Auto has them for about $30. PN# S603...

I have a bunch of LVS TMs on my hard drive that I don't need but I have been asked my some members on here for them. They are too big to email and too big to attach to a message on here. Do any of you Moderators have any suggestions? I don't want to delete them as I know they are difficult to...

When you did your manual override, did you disconnect the light blue wire from the GPC and run it to a switch? Ive seen that on here several times but it doesnt seem to me like that would bypass the module. I will try it though. Since you've dont your override, have you had any trouble starting...

Done that. Nothing. Checked the glow plug wires and Im getting nothing when the engine is warm. Works fine when engine is cold. According to the schematics, there should be a recycle on the gpc but after the first cycle, my gpc doesnt cycle again. I traced and checked for voltage and continuity...

Ive looked all over this site and the TMs and either Im searching for the wrong thing or its not here but Im having problems with my M1008 starting when the engine is warm. If I shut it down and let it set for 5 minutes, it fires right up. Any longer than 5 minutes and Ive gotta crank 3 or four...

That truck is gorgeous!!! I love the trailer bed!!

Tires This guy has ridiculous deals on tires. Don't know if he's stealing them but Ebay wil be responsible if he is!!! Berg Military Tires items - Get great deals on H1 Hummer, GoodYear items on eBay Stores!

Replaced the stock fuel pump with one from a 6.5L. PITA but worth it since I didn't have to buy a new one. Had to cut the inlet tube and thread it to put a fitting on and had to readjust the steal outlet line a bit but all went smooth. Did the oil pan and tranny pan/filter last week.....still...

Did that O/D bolt in with now mods required?

So I pulled all 8 plugs today and the 3rd plug back on both sides are broken. Second time in 2 months this has happened. I ordered new injector nozzles from RockAuto, should be in next week. Don't know if this will solve the problem but I hope it will. Any suggestions?

Thanks Dave, I appreciate that.

Did the HMMWV Rims bolt up perfect or did you need spacers? I just tried to put HMMWV rims on my M1008 and the rim actually hits the tie rod. I didn't see anything in your thread that mentioned spacers or mods. Thanks.