Search results

OOPS! You can use a die grinder with a fine point burr and try grinding the extractor out. Alot of times the vibration of the grinding will loosen the broken extractor piece.

COOL! I think I'd sell my truck for one of those.

So ,the M105 A2 wheel cyls...the axle with the 3, 1/4 20 screws that hold the dust cover on..are NOT the same as the M35A2? Are they unique to the A2 or are they used on another vehicle?

If the hole you drilled is very, very close to center of the broken capscrew, drill the old , broken capscrew to the size hole needed to tap threads for the existing bolt size. The drilled hole SHOULD remove all material, except for the threads. You can then, peel the left over threads out of...

Bruce, I think the upper is just wrapped stick hose. Snap some pics of them both...top and bottom. I have a boat load of hose. If it is straight, measure it and let me know.

Can you imagine what kind of nightmare it must have been to figure out a clutch linkage? Wonder how long it took them to figure out all the different mods...e-brake, clutch, throttle...what did they do for gauges? Anyone got a pic of the drivers area on this truck? Those people were thinkin' man!

heavychevy..CA as in California or Canada? Where you at?

I think that will be a hand made one off job. Looks good though! Looks off set at the bottom for tire clearance and that would help with the wt. distribution too.

Are they 3/4 diameter? Do you need the ones with a flat spot in them?

At the top of the deuce forum, there are some stickies..read them. Download at least the TM 9-2320-361-10 operators manual and read that. Shop around and, if possible, have someone who has a bit of knowledge on what you wanna get go with you to check it out. Use the member locator map and see if...

RE: M578 I don't think it will see the road. We kind of messed around and thought about taking it into the field next door, but I don't want to draw any negative publicity to the museum. If LA counties finest came by, they might not think it was such a good idea. It was a blast to drive around...

That was good reading...think i'll print it off and keep it...for future reading! There have been some of the B1's at some of the air shows out here. They leak the same way. I asked one of the flight crew why the aircraft had drip pans under it.." did you have a failure on the way in?" He said...

Went for 3500. PLUS the lien and e-bay fees....$7450.00. Sure hope it runs! Anyone here get it?

RE: M578 It made smoke, but never lit off. That fan sure draws some amps! The batteries were dead, dead. I think the museum is gonna get some new ones, but the ones in it were almost dry. They could be brought back with a fast charge then back off to a trickle...maybe, I'll see what Craig wants...

Is it the #11 bolt? It looks like it just holds the plate onto the housing.

WOW, that's the same pan? Looks good Mike. The inside of your engine looks clean.

Not as easy as just un bolt and bolt the new ones up. There is cutting and grinding and drilling involved, but it is easy. The drivers side is gravy, if you try to use the existing holes, the light hits the frame. you need to make an extention...no biggie. The pas. side takes some cutting...

Mike, You can put the composite lights on the trailer that has/had the old round lights. There are just a couple of mods to do. The wiring is the same. The free trailer had the round lights and the GL trailer ahd the composites, I wanted composites, so, I just swapped them...took a bit of...

OK the stuff on you tube is ready, http://www.youtube.com/watch?v=UaatcixQJ8g&feature=related http://www.youtube.com/watch?v=PrkvD0pu_Zw http://www.youtube.com/watch?v=6ThH0OtRfMg http://www.youtube.com/watch?v=Fzqqv8NAwH8&feature=related Floyd, The last two vids will let YOU listen to heavy...

For the deuce, TM9-2320-361-10, Dec, '88 For the 105, TM9-2330-213-14, Jan'64 TM5-1080-250-12&P, Jan '03, for the radar scattering, desert camo netting. Got a mess of TMs in PDF..I HATE pdf! Rather have paper in front of me.