• Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!

  • Microsoft MSN, Live, Hotmail, Outlook email users may not be receiving emails. We are working to resolve this issue. Please add support@steelsoldiers.com to your trusted contacts.

Search results

  1. Daybreak

    3 piece grounding rods

    Howdy, Funny you should talk about ground rods. I just installed 14 ground rods here. Electric wire fence. 5/8 galvanized 8ft, t-post pounder to start, and then a Milwaukee jack hammer with ground rod driver bit.
  2. Daybreak

    mep 803a not starting

    Howdy, Get a battery charger. Charge each 12v battery separately to bring them back to life. Or.. Get new batteries.
  3. Daybreak

    Grounding Question: Beating a dead horse

    Howdy, Your setup is code compliant for how they are constructed and distanced. This is actually still a standard practice for a farm with livestock. Outbuildings having there own grounding. NEC covers most standard uses, and some they have exception on the books. You would need a electrician...
  4. Daybreak

    New guy here with an 803a

    Howdy, Welcome to the forums. You could start here. MEP-802/803 Filters and Parts The second post has quick links to lots of stuff. The fuel/water separator is put on dry by King Kong. 8) The third post has the link to the manuals. It sounds like you are off to a good start. Attach a...
  5. Daybreak

    Found time to pick up a super nice mep-802a today

    Howdy, Military MEP generator reset information MEP-802/803 Filters and Parts the 2nd post has quick links to lots of stuff. Break-In oil for the low hour MEPS The TQG 10kw and smaller do not sync and run in parallel. Because of the manual adjustments, it would be out of balance. 15kw and...
  6. Daybreak

    2X MEP-802A Dead on Arrival... won't crank... Crank Relays Dead

    Howdy, Open the control panel and review each of the relays. There are 2 types of relays The far left looking is the switch, the other 5 are standard You can remove them and put them back to ensure a connection. Check the diode panel, check the CB1 is pushed in, and check the FU1 fuse...
  7. Daybreak

    Good source for auxiliary fuel hose & fittings?

    Howdy, The hose blue print could be printed and taken to a hose maker. He would know exactly what is needed by looking at what is written. That is there territory. :)
  8. Daybreak

    My 802a in the northeast thread

    Howdy, YEP. Every MEP-802 and MEP-803 has had the fuel/water filter put on by king kong dry. Watch the sharp edges. Use a exact fit filter wrench, or a heavy strap wrench. And really really pull hard, and pull harder. It does actually come off.
  9. Daybreak

    2011 Mep 803 wiring for house

    Howdy, Connected to a house, bonding strap disconnected. In the middle of a field, bonding strap connected, and ground rod in the ground.
  10. Daybreak

    MEP-803A After Action Report

    Howdy, The new equipment keeps getting smaller. My Essex A427 load bank is from around early 1970's
  11. Daybreak

    MEP-803A After Action Report

    Howdy, Isn't just a bummer that you don't know what to do with all that power. :) I put up a few different videos under varying loads on some MEP-802A, MEP-803A, and MEP-1030. Acquired a Military surplus load bank
  12. Daybreak

    Just picked up an MEP-803a

    Howdy, MEP-8xx startup routine
  13. Daybreak

    Good source for auxiliary fuel hose & fittings?

    Howdy, Of course there is a sticky at the top of the auxiliary section. sticky: Generator AUX fuel connections There is even a PDF with the 37 degree hose end information for getting a custom hose made.
  14. Daybreak

    Our first real outage with the 803A

    Howdy, I don't know about that. I have 5 tractors that are made to work. I have no problem running any tractor powering my PTO generator. The again, the PTO generator is a 30KW and spins at 1800rpm.
  15. Daybreak

    Our first real outage with the 803A

    Howdy, Yep, I have a friend up there in Penobscot. He is on generator as well. No quick time planned for fixes. He said lots of pines down on the lines all over. Which pin & sleeve unit did you go with?
  16. Daybreak

    Just picked up an MEP-803a

    Howdy, No military generator will start with battle short on.
  17. Daybreak

    No longer need assisatnce near Winchester, VA

    Howdy, I guess you are on your way. I am right off Winchester, VA I would have blown there mind if I rolled up with Farm F Tags and drove off. Nothing they can do. :)
  18. Daybreak

    MEP-803 - Fluctuations in Hz - Puerto Rico - HELP!!

    Howdy, You have come to the right forums. :) I know parts and pieces might be hard to come by. You can start here. MEP-802/803 Filters and Parts The 2nd post has quick links to a lot of stuff. A little farther is the post with quick links to the TM's which you will need. TIP: Turn the S-1...
  19. Daybreak

    Just picked up an MEP-803a

    Howdy, I see you said it had holes poked in the tank. There might be major issues with your unit. The hole along the skid, is the fuel drain. A A3816 well nut goes there and the fitting screws into that You will find the quick link to that in the thread. Infamous well nut, or you could go with...
  20. Daybreak

    803a won't restart

    Howdy, It sounds like you jumped the gun way to fast and did not want to listen to what was needed to be done. I specifically asked if it was properly primed after the fuel filters were changed. You could very easily had a air pocket which would not be vacated since you had it running. It was...
Top
AdBlock Detected

We get it, advertisements are annoying!

Sure, ad-blocking software does a great job at blocking ads, but it also blocks useful features of our website like our supporting vendors. Their ads help keep Steel Soldiers going. Please consider disabling your ad blockers for the site. Thanks!

I've Disabled AdBlock
No Thanks