Search results

I am not sure about 2 problems until you get the one injector that isn't working right...since you swapped it left to right and the smoke traveled with it that injector would be a issue....any chance they sent you a wrong one but boxed right? I think they are marked to show lbs or injector...

Nice....You ever drive south on Lewisberry road off Canal stop by n say hi....can't miss my container next to my garage!

Please don't take this wrong as I highly respect all the info you give on here but I disagree with not having the pickup off the bottom of the tank. The reason is with my one tank that had the pick up from the top to about 8 inches from the bottom filled up with water and junk over time then...

I put a tilt steering in mine that I got out of a 1992 blazer...paid 50$ for it and had the key in it ready to go...my 15 year old son swapped it out by himself...not hard at all...can get the linkage lined up right at the same time as long as the transmission is ok. I needed the tilt...the...

I have a 803 with 2 275 gallon home heating oil tanks feeding it...they have the drain at the bottom so I hooked to that with a shut off and filter then steel line to the genset...works great.

I doubt the filter will be much resistance then at that flow rate...the tank is 5 gallons I think on the 802 so it doesn't take much....just thinking of keeping it primed or getting it that way...you'll know once the genset calls for fuel! Mine is gravity so I haven't had any problem feeding...

As long as your aux pump can pull it through it won't hurt having extra filter capacity...maybe a priming ball to get it going or a cheap carb 6lb electric pump if need be...they are cheap...can run the pump off the aux pump wiring so when it turns on it'll turn on the filter pump too. Dig the...

Have you tried to turn the headlight switch that you pull out to turn on the lights? Clockwise should make them bright and counter should make them dim.

I have seen 2 of these very recently for sale...I was thinking of getting one to add to my stash of fuel!! Wish the diesel was .89 a gallon still.

The hook up is pretty much up to the code of where you are...I did the entire house setup with a manual switch outside...that means I needed a 200 amp switch since the house is setup for a 200 amp service and had to match even though I'm only pushing 52 amps at 220...I think the 802 does 37 amps...

I don't know what a ibc is but I just did the line to my aux fuel a few weeks ago...JIC size was 6 if I remember right...I got it from my local hydraulics company, had a line made up to go right on. I took the cap that covers the aux line when not in use to the store. I'm not sure florida has...

Your dads right for sure...typically it's not the coolant but the water used to mix it...if you change coolant a lot it won't matter much but something that sits, like these gensets, with a charged up set of batteries wreaks havoc on aluminum parts...making sure you have good clean low...

I don't know the part numbers and obviously you have a paper copy of the tm and need parts 3,4 and 5...any chance you looked at the online tm available in this site? If you can't find it I can try to look them up in the tm online here...not sure if you have easy access or not. I'd check the...

So I'm not sure if I got the number from his post but it looks like, according to it, I did get the correct fuel line. Brand and part number. Thanks for verifying! Rich. Sent from my SM-G955U using Tapatalk

I'm not sure if it's exactly stock by the TM...but it is the spec size of 3.5mm inside diameter with the mesh outer and diesel use...I couldn't find that size anywhere but online...there's a pic of the company I bought it from, a post 1 January. Mine got shipped out of Baltimore but I think they...

Took 2 weeks but I finally got the return fuel line in the mail!! Took all that time to come from Baltimore 45 minutes north to here! The nitrile fuel return seals look like they should work fine. I will be going at this repair tomorrow!

That's good news!! Weird thing to have disconnected though. Hope it works good now.

click on my link to my thread....middle pic of the VR,,,,to the left is a fuse...it is hooked to the quad pin 8 the other wire came off pin 8 originally.

Well if you have other 803s then I guess you can swap one...just see if they have the fuse added to it...then swap that too...hate to burn up another one! Sent from my SM-G955U using Tapatalk