Search results

Elohim1 and I went to haspin today and took some pic's..We also drove the deuces all the way around haspin and stayed on the main trail with out a problem..2 miles or so anyway..Lots of places we could have played but we just did a little hill climbing and went home...

Hi All,Elohim and I want to finnish our deuces off with the correct markings etc but we don't have a clue as to what size numbers and letters etc and where they go...I found a site that looks like they have everything we need to do the job but we don't want to order anything untill we are sure...

Ok,I have had problems with my brake lights not working or working but dim and sticking on VERY dim...I decided to get a new 3 lever switch and in the mean time I bought 2 pressure switches..One new one and one used one..Ok I replaced the 3 lever switch and no help..I tested the wires that plug...

I parked the deuce yesterday with it leaning a little to the passenger sit and now I have a little grease on my inside rear wheel..Looks like it has an axle seal leaking :banghead: ..It looks like I'll have to R&R the seal...How hard is it to replace it?? The shop I had my tires done at said...

Hi All,It looks like my master cylinder is leaking some and it looks like it's leaking from where the brake push rod goes into the front where the rubber boot is..I want to check the fluid but the place I would think is where I should check the fluid has what looks like a brake line attached to...

Ok,I ordered a brake light pressure switch thinking it may be the problem with my brake lights low voltage and I have a question..Will I have to bleed my brakes after the R&R of the pressure switch ?? I don't know if there is brake fluid or air that work's the switch..I am also looking for a new...

Well I took 8 of the 12 900x20 NDT tires I bought from Berg Supply down to a shop at a truck stop near me this morning to get mounted..I got there at 10:30 and left at 4:30 :freaked: They never worked on anything else the whole time I was there either..They had a heck of a time breaking the...

Hi All,I just ordered some 900x20 deuce tires and they are supposed to be 75% or better tread..Well I was wondering how deep is the tread on a new NDT tire ??I checked the TM on tires and it didn't say what they were new .. My 2 best tires on mine now is a little over 1/2"..The TM said to...

Hi All,Well I decided to go the low-tech route and rattle can my deuce with the Olive Krylon from walmart..$2.65 a can and I figure about 20 cans and a couple cans of primer and about a day of wire brushing,Taping,Priming the bare spots and painting..Oh and a lot of can shaking :banghead: ...I...

Hi All,Another dumb question :redface: But every time I open the drivers door on my deuce I see this little tag and I have no idea what it stands for..I did a search and no results...What is MWO ???

Hi All,I would like to know exactly what tools go in the rack on the side of my deuce..I see the racks on just about every deuce I see but there are never any tools in the rack..I have a short handle shovel and picks etc but I think my shovel is a little long for the rack..Any help would be...

Hi All,I have a problem with my brake lights..They work w/o the headlights on but not as bright as they should be I don't think..When I move the light selector switch from the brake light position to the headlight position the brake lights don't work..It kinda looked like they came on but were...

Hi All,It got down in the low 30's the past couple days and when I went to start the deuce I had to crank it longer than usual..I cranked it for about 3-4 seconds and flipped the manifold heater switch and held it to the right for about 3-4 seconds and it fired up..How do I tell if the heater...

Hi All,My friend Chris (Elohim1) had a small leak spraying from his radiator so we removed it and took it to a small shop to have it repaired..Well after checking it out the guy said it was rotted and he wouldn't repair it..Now he needs a radiator :banghead: Any ideas where to get one and maby...

Hi All,I have the CD with a bunch of TM's but after searching for hours I still can't seem to find detail's for adjusting my brakes on my deuce..Anyone know exactly which TM covers it ? Thanks...Fred

Hey All,I mounted a 2" receiver on my deuce yesterday and decided to try it out today..I loaded my CJ7 onto my trailer and pulled it about 70mi over to Haspin Acres in Laurel Indiana this morning..It did great but I couldn't hook up any trailer lights since the trailer lights were 12v..It got a...

Hi All,I did a search and couldn't find much so here it is..I have a problem with my brake lights..They worked when I first got it but I didn't try them with the lights on..Now when I have the lights on the tail lights are nice and bright and when I hit the brake the brake light comes on dim but...

Hi all,I had a big hole in the J pipe and didn't really want to spend $250 + fir a SS J pipe rite now...I drove the deuce down to the muffler shop and thinking the pipe was 3" asked them if they could cut out the bad spot and bend me a pipe to fit..Well the pipe is 3.5" instead of 3"..I had them...

Hi all,Elohim1 and I just installed the NAPA #60-750 Arms and the NAPA Exact Fit #60-011-1 Blades and they worked fine..Mine didn't have any arms on it when I bought the truck but his did..It seems it had 2 different type wiper arms and I was just wondering which one of them was the correct one...

Hi All,I noticed that both my wiper arms are missing from My deuce and I will need to get some so does anyone have any idea where I should look to buy a set? I also need a set of windshields and frames since my frames are rusted and cracked the glass in both sides..I still need a J pipe for it...