- 1,396
- 392
- 83
- Location
- Feasterville, Pennsylvania
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
Deuce with Cummins 6BT Info thread
- Thread starter 59apache
- Start date
.JPG "T-08092016-13 | M35 Cummins 16-13 (24).JPG")
HanksDeuce
Well-known member
- 1,081
- 242
- 63
- Location
- Prairieville, LA
The intake piping looks funny on that truck. My truck has the turbo compressor inlet closer to the radiator, and the exhaust dumps into the downpipe near the firewall. It looks like this truck has the compressor inlet piping on the firewall side, but how is the downpipe routed near the radiator?
Eastern's 6bt pic
.JPG)
My 6bt engine pic
davidb56
Well-known member
- 1,020
- 1,237
- 113
- Location
- Bonners Ferry Idaho
be
because yours has a intercooler, and the other one doesn't......The intake piping looks funny on that truck. My truck has the turbo compressor inlet closer to the radiator, and the exhaust dumps into the downpipe near the firewall. It looks like this truck has the compressor inlet piping on the firewall side, but how is the downpipe routed near the radiator?
Eastern's 6bt pic
My 6bt engine pic
HanksDeuce
Well-known member
- 1,081
- 242
- 63
- Location
- Prairieville, LA
I don't think so. Here's another one without an intercooler (from page 1 of this thread). Air filter feeds front of turbo (not the firewall side). Of course the turbo in the picture below sits up much higher than the Eastern Surplus listed engine.
I have no clue if there was a contract with plans on one way to do this, or some of these pictures are custom M35A2s with 6BT builds like mine.
davidb56
Well-known member
- 1,020
- 1,237
- 113
- Location
- Bonners Ferry Idaho
the one turbo is flipped. air side is at the rear, the one in this pic has the air side in the front. 1989-91 cummins 5.9 were not all intercooled. Also follow the air intake manifold to the turbo, it would be going to the front of the engine if it was intercooled, as the intercooler would be in front of the radiator....Both are piped right back to the turbo.
Last edited:
davidb56
Well-known member
- 1,020
- 1,237
- 113
- Location
- Bonners Ferry Idaho
@ Hank...BTW your truck is super clean. I got some good mod ideas from your build for my truck.
radog3
New member
- 1
- 0
- 1
- Location
- Rochester Illinois
I'm hoping to figure out the story on my cummins conversion 71' m35a2. The tan cummins in the first picture is mine and I couldn't help but notice the alternator bracket is the same as the second picture. I've since swaped in an aftermarket radiator because the original was torn up by the winch cable when I bought it. The other pictures are my engine mounts etc. I'm just curious if the military actually converted a few of the trucks themselves or if a company was selling a conversion kit.
Attachments
Last edited:
- 3,256
- 3,352
- 113
- Location
- NORTH (Canada)
Deleted - TapaTalk did not show that I was replying to the very thread I was quoting. Sorry!
Last edited:
Hi, writing you from Brazil. I´m not sure whether the truck with intercooler aplication is yours - but even if not, maybe you could tell me who can give me some hints about - thinking about putting it on my M35AC Cummins 6BTThe intake piping looks funny on that truck. My truck has the turbo compressor inlet closer to the radiator, and the exhaust dumps into the downpipe near the firewall. It looks like this truck has the compressor inlet piping on the firewall side, but how is the downpipe routed near the radiator?
Eastern's 6bt pic
My 6bt engine pic
HanksDeuce
Well-known member
- 1,081
- 242
- 63
- Location
- Prairieville, LA
The M35A2 with intercooled 6BT is indeed mine. I ended up having to use a longer military truck hood (dump truck?) because the radiator/intercooler assembly stuck out too far.
For more information on fitting the intercooler visit the following, https://www.hanksdeuce.com/intercooler_mods.htm
GM-M1008
Member
- 200
- 8
- 18
- Location
- Weatherly, PA
Mines intercooled. It actually has a cummins part number on it if you’d like. Fits behind the stock grill and hood.
Hi, sounds interessting - would like to get that part number
thanks
... also if you had some images of your application, would be very much appreciated
GM-M1008
Member
- 200
- 8
- 18
- Location
- Weatherly, PA
I’ll get the part number off it when I’m at the truck.
Attachments
Hi, thanks a lot - now I´ve done a google on that part number, but did not get any indication
could you help me with some further information about that intercooler?