spankybear
Well-known member
- 884
- 911
- 93
- Location
- WA
Driver's Door
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
Well, I done did it. Won a m1078. Need to get it home... In Wahington - any suggesti
- Thread starter spankybear
- Start date
spankybear
Well-known member
- 884
- 911
- 93
- Location
- WA
Does anybody have a lead on a door handle... Not that one this one here
https://c1.staticflickr.com/1/836/40902400994_a0b3c8430b_h.jpg
https://c1.staticflickr.com/1/836/40902400994_a0b3c8430b_h.jpg
- 629
- 24
- 18
- Location
- Port orchard, WA
Couldn’t you make it? Looks like round stock beaten and bent, couple holes drilled. Or get fancy and make one like mine.
I saw one that was an arm rest also, maybe Wes's 5 ton. Would be nice to do both, arm rest and closer.
spankybear
Well-known member
- 884
- 911
- 93
- Location
- WA
I have found those but I am not too sure what vintage those are. If you look at the 24P fig 188 item 8 it shows the ones I am looking for.
- 6,556
- 13,941
- 113
- Location
- Hawthorne, NV.
Spanky. Have you asked Alex Gordon at Idaho Motor Pool, if the M1078 he is parting out has some door handles? Can't hurt to ask!
Duckworthe
Member
- 329
- 23
- 18
- Location
- San Diego, Ca
https://c1.staticflickr.com/1/836/40902400994_a0b3c8430b_h.jpg
On my truck, those are the "OH, S*%T" handles above the doors. I have the ones like in post #103 on my doors. But hey, If it works!
On my truck, those are the "OH, S*%T" handles above the doors. I have the ones like in post #103 on my doors. But hey, If it works!
spankybear
Well-known member
- 884
- 911
- 93
- Location
- WA
Thing is I don't see any holes that would line up to that other type of handle... strange as ever picture I have looked at has the other handle and not what I have.
Duckworthe
Member
- 329
- 23
- 18
- Location
- San Diego, Ca
What year is your truck? Maybe it was one of the last trucks on a run and they just used whatever they had left? I doubt that's the case. I have known people who have worked in auto industry and in the military refurbishment factories. Some just do things as a prank or a dig at a supervisor and the item never gets reported or spotted. Then the next person says, "well I'm not the door pull guy and that must be what the truck was supposed to have on it. Not my job or my issue." sad but true
spankybear
Well-known member
- 884
- 911
- 93
- Location
- WA
It's a 1995 so I don't think it's was at the end of production. Who knows...
- 5,637
- 381
- 83
- Location
- Spring Branch, TX
Might have been a replacement door. There was a lot of issues with folks opening the doors with the cab tilted and maybe the new door shells came without handles.
spankybear
Well-known member
- 884
- 911
- 93
- Location
- WA
The 189.99 dollar starter I got works awesome!!! Now I can move her around!!! 100% runner now. Not too bad given the price I paid!!!
spankybear
Well-known member
- 884
- 911
- 93
- Location
- WA
I really wasn't trying to win this auction. I have been watching GP for awhile and wanted to learn the bid mechanics on GP. I threw in a token bid, one bid of 3800.00 just to see how it worked. Didn't even dream I would have won this and too this point only one other truck in Washington went for less. It was a stripper and sold for 3100. Every other truck went for 4000 and above.
So I went up and got a cup of coffee and came back and sat down at the computer. I click to see how much it sold for and low and behold I won... So began the scramble and the start of this thread.
When looking at the pictures I had a good feeling the truck was a runner. The only real issue I saw was the missing voltage gauge.
The yard apes put a huge dent on the front left side. I have worked that out and so far I am happy with what I have done. I have never done any body work but watching a few vidoes on the youtubes I think I have it good enough.
The floorpans are rusty but nothing to bad. This is Washington and it rains and these trucks leak... rust happens. I have replacements i'll be welding in. Again never done that but lots of youtube.
Need to take the turret cover off and see what's up there rust wise as it is where it leaks. Also need to seal it up. But I didn't see anything major with it still in place. I'll find out soon enough.
Windshield will also need to come out. 1) there's a crack and I see some rust. This is on the back burner.
I'll need to replace the heat and sound insulation. I am remove the old stuff to get to the rust underneath. The old stuff holds water... and come off very easy when it's wet.
Need to replace the upper sway bar bushing... they are gone. I have the bushings and steel sleeves just need to find the washers.
There's a few OCD things I will need to do.
Almost forgot how much I enjoy working on military vehicles... But the body it protesting
So I went up and got a cup of coffee and came back and sat down at the computer. I click to see how much it sold for and low and behold I won... So began the scramble and the start of this thread.
When looking at the pictures I had a good feeling the truck was a runner. The only real issue I saw was the missing voltage gauge.
The yard apes put a huge dent on the front left side. I have worked that out and so far I am happy with what I have done. I have never done any body work but watching a few vidoes on the youtubes I think I have it good enough.
The floorpans are rusty but nothing to bad. This is Washington and it rains and these trucks leak... rust happens. I have replacements i'll be welding in. Again never done that but lots of youtube.
Need to take the turret cover off and see what's up there rust wise as it is where it leaks. Also need to seal it up. But I didn't see anything major with it still in place. I'll find out soon enough.
Windshield will also need to come out. 1) there's a crack and I see some rust. This is on the back burner.
I'll need to replace the heat and sound insulation. I am remove the old stuff to get to the rust underneath. The old stuff holds water... and come off very easy when it's wet.
Need to replace the upper sway bar bushing... they are gone. I have the bushings and steel sleeves just need to find the washers.
There's a few OCD things I will need to do.
Almost forgot how much I enjoy working on military vehicles... But the body it protesting
coachgeo
Well-known member
- 5,147
- 3,463
- 113
- Location
- North of Cincy OH
Where you getting the weld in floor pan ?
MrGoodwreck
New member
- 20
- 8
- 3
- Location
- WA
I don't know what happened to me today, but my back is soreAlmost forgot how much I enjoy working on military vehicles... But the body it protesting
How did you feel when we heard what the Fire Dept. paid for theirs?
spankybear
Well-known member
- 884
- 911
- 93
- Location
- WA
A guy here in the northwest has some scrap cabs. Sawsall and some work I have me some floorpans.
With that said there is a guy that has some cabs for a good price. If I had a way to lift the cab I would go that route, well maybe... All I know is if i really screw up with the floor pans I have an out.
Last edited:
spankybear
Well-known member
- 884
- 911
- 93
- Location
- WA
got the turret cover off today to see why it's leaking... Well found rust and holes... I know what the first thing I am going to be welding...
On a side note I found the Armory that the truck came from
On a side note I found the Armory that the truck came from
FullSpecial
Active member
- 247
- 108
- 43
- Location
- Denton TX
Stop in and see if they will talk to you. Couldn't hurt, might even get some history.
The Early LMTV are rusting like crazy- no corrosion protection until 97. Matter of fact. That and the resulting delay is the reason S&S lost the contract. These truck cabs looked like Swiss cheese already at the Sealey Plant and had holes while they were waiting to be installed on the trucks.