- 673
- 894
- 93
- Location
- SW Va, Roanoke County
Started plumbing, fill, wash, and porcelain god positioning
Last edited:
-
Steel Soldiers now has a few new forums, read more about it at: New Munitions Forums!
MV Addiction filled. Reis the Beast M1078A0 is born
- Thread starter M1078MAN
- Start date
Phoenix77
Well-known member
- 240
- 543
- 93
- Location
- Greenville, NC
Is that an S-280, or a smaller shelter? 
- 673
- 894
- 93
- Location
- SW Va, Roanoke County
Its a S178, 11'4" inside length, 6'7" inside widthIs that an S-280, or a smaller shelter?
- 673
- 894
- 93
- Location
- SW Va, Roanoke County
\\MAIL CALL//
Recd a nice over counter 18" Stainless Rectangle Sink
Recd a nice over counter 18" Stainless Rectangle Sink
- 673
- 894
- 93
- Location
- SW Va, Roanoke County
\\MAIL CALL//
Yesterday was a great day, received my long awaited 3/8x16 RIVNUTS. Now I can start putting habitate back together
Yesterday was a great day, received my long awaited 3/8x16 RIVNUTS. Now I can start putting habitate back together
- 673
- 894
- 93
- Location
- SW Va, Roanoke County
\\MAIL CALL//
Just about got all the parts for the exhaust/water heat exchanger and exhaust system just waiting on elbow reducer
Muffler will not be used and is shown for id/od size comparison only
Sorry, should have included source for heat exchanger
Search FLEEBAY for: HEAT-X 200XS Heat Exchanger WP 400 PSIG
Just about got all the parts for the exhaust/water heat exchanger and exhaust system just waiting on elbow reducer
Muffler will not be used and is shown for id/od size comparison only
Sorry, should have included source for heat exchanger
Search FLEEBAY for: HEAT-X 200XS Heat Exchanger WP 400 PSIG
Last edited:
coachgeo
Well-known member
- 5,147
- 3,463
- 113
- Location
- North of Cincy OH
diesel heater exhaust? what is the exchanger unit?
- 673
- 894
- 93
- Location
- SW Va, Roanoke County
Coachgeo
Heat Exchanger
Search FLEEBAY for HEAT-X 200XS Heat Exchanger WP 400 PSIG
\\MAIL CALL// on a sunday
I really like getting packages on Sunday
3/4 Street and copper plug
Turned the 3/4 plug down on the mill to 24mm ID and soldered everything together. Ready for install
Heat Exchanger
Search FLEEBAY for HEAT-X 200XS Heat Exchanger WP 400 PSIG
\\MAIL CALL// on a sunday
I really like getting packages on Sunday
3/4 Street and copper plug
Turned the 3/4 plug down on the mill to 24mm ID and soldered everything together. Ready for install
Last edited:
- 673
- 894
- 93
- Location
- SW Va, Roanoke County
Finished product..except for trimming the pipe to outside flange
coachgeo
Well-known member
- 5,147
- 3,463
- 113
- Location
- North of Cincy OH
that is a very reasonable price.Coachgeo
Heat Exchanger
Search FLEEBAY for HEAT-X 200XS Heat Exchanger WP 400 PSIG
\\MAIL CALL// on a sunday
I really like getting packages on Sunday
3/4 Street and copper plug
Turned the 3/4 plug down on the mill to 24mm ID and soldered everything together. Ready for install
some have made use of an EGR removed from various cars for same purpose. Sometimes you can get them for free
- 434
- 206
- 43
- Location
- Lynchburg, VA
So what is the plan with the scavenger? Use it to pre-heat water in a tank? Or send it through there on way to on-demand unit? Do you manually send it there or is that the default? How do you account for cold weather situations?
- 673
- 894
- 93
- Location
- SW Va, Roanoke County
Its only to keep water from freezing,
There will be a 12v circ pump that when the heater is blowing due to temps below preset as set on guage for habitat, the pump will come on and circulate warm water through the plumbing system and back to the tank to keep things from freezing.
Not sure of the efficency of the exchanger/and heater exhaust output, so that may change how I activate the pump
I figure with the temps in the habitat up at a constant, the R factor of the shelter, and all water related components inside the shelter, I am hopeful that I can keep water from freezing
I went with this heatexchanger unit as the diameter of exhaust input/ouput is larger then the jp8 heater unit, its straight pass through and I was thinking backpressure in this case would not be good
Yup-thats where the idea came from, I have been studying his videos for awhile. Hopefully an improvement..
There will be a 12v circ pump that when the heater is blowing due to temps below preset as set on guage for habitat, the pump will come on and circulate warm water through the plumbing system and back to the tank to keep things from freezing.
Not sure of the efficency of the exchanger/and heater exhaust output, so that may change how I activate the pump
I figure with the temps in the habitat up at a constant, the R factor of the shelter, and all water related components inside the shelter, I am hopeful that I can keep water from freezing
I went with this heatexchanger unit as the diameter of exhaust input/ouput is larger then the jp8 heater unit, its straight pass through and I was thinking backpressure in this case would not be good
Yup-thats where the idea came from, I have been studying his videos for awhile. Hopefully an improvement..
Last edited:
- 673
- 894
- 93
- Location
- SW Va, Roanoke County
So someone was asking about shelter thickness, thought I would post this picture of the wall I just drilled out
.
.
- 673
- 894
- 93
- Location
- SW Va, Roanoke County
Some more progress today, heater mounted, heatexchanger installed, outlet installed..just need fuel and electrical
Third From Texas
Well-known member
- 2,766
- 6,498
- 113
- Location
- Corpus Christi Texas
Attachments
- 434
- 206
- 43
- Location
- Lynchburg, VA
Wow that's an R of somewhere between 20.25 - 27. Not too shabby.
- 673
- 894
- 93
- Location
- SW Va, Roanoke County
Outstanding day..We are producing power via PV
That's when they started caring about the time spent in the shelter..haha..serious r factor..are the walls that thick
That's when they started caring about the time spent in the shelter..haha..serious r factor..are the walls that thick
Last edited:
- 673
- 894
- 93
- Location
- SW Va, Roanoke County
Making some more progress.. and making your own power is freedom
Last edited:
- 673
- 894
- 93
- Location
- SW Va, Roanoke County
Looking for some help, I need to make an ingress/egress to the habitate so that a 75year young person who had a mild stroke a few years ago, can climb up into the habitate. I have scoured the internet for cheap DIY options, but have not really found anything.
Was thinking about a ramp style, like a Uhaul has, with a hand rail, or steps of some sort with wide gentle risers..maybe a small 4x4 platform at the door, so you are not going straight from door to drop down on to stairs
Any suggestions are greatly appreciated and most certianly welcome
Was thinking about a ramp style, like a Uhaul has, with a hand rail, or steps of some sort with wide gentle risers..maybe a small 4x4 platform at the door, so you are not going straight from door to drop down on to stairs
Any suggestions are greatly appreciated and most certianly welcome
coachgeo
Well-known member
- 5,147
- 3,463
- 113
- Location
- North of Cincy OH
Maybe two used bumper mower/chair lifts rehabbed and modified? Have them sit side to side of one another but one placed higher up. I say two cause one will not raise high enough. so you end up with two.... each their own landing.
sit in a chair or stand on one as it raises as high as it will go. then you transfer to the one that raises to the height of the door of habitat.
otherwise copy the motorcycle lifts of others on here who put bikes on back of their expedition rigs. Most are winch raised platforms on rollers.